ORIGINAL RESEARCH article

Front. Built Environ., 13 October 2026

Sec. Urban Science

Volume 12 - 2026 | https://doi.org/10.3389/fbuil.2026.1959364

A spatial GIS–AHP framework for integrating hybrid renewable energy suitability with urban growth planning in arid regions

  • 1. Department of Architecture, College of Engineering and Information Technology, Onaizah Colleges, Qassim, Saudi Arabia

  • 2. Department of Architecture, The Higher Institute for Engineering and Technology of Obour, Cairo, Egypt

  • 3. Department of Architecture Engineering, College of Engineering and Design, Kingdom University, Riffa, Bahrain

  • 4. Department of Architecture Engineering, Faculty of Engineering, Minia University, Minia, Egypt

  • 5. Interior Design Department, College of Architecture Engineering and Digital Design, Dar Al Uloom University, Riyadh, Saudi Arabia

  • 6. Department of Architecture Engineering, Alasala Colleges, Dammam, Saudi Arabia

  • 7. Department of Architecture Engineering, Al-Safwa high institute of Engineering, Cairo, Egypt

  • 8. Civil Engineering Department, Faculty of Engineering, Fayoum University, Fayoum, Egypt

  • 9. Department of Civil Engineering, Faculty of Engineering, Assiut University, Assiut, Egypt

  • 10. Department of Civil Engineering, College of Engineering and Information Technology, Onaizah Colleges, Qassim, Saudi Arabia

Abstract

Introduction:

Urban expansion in arid regions drives vital socio-economic development but places significant pressure on urban systems through land competition and infrastructure strain. To address these challenges, this study evaluates the spatial suitability and distribution of solar photovoltaic (PV), onshore wind, and hybrid solar-wind energy systems, investigating their spatial interactions with proposed urban expansion zones in Al-Qassim, Saudi Arabia.

Methods:

A GIS-AHP framework was developed using 13 criteria for solar PV and 12 criteria for onshore wind energy. Spatial datasets were standardized, reclassified, and synthesized via weighted overlay analysis. Hybrid suitability was determined by integrating the individual solar and wind models, while a post-model spatial interaction layer was incorporated to evaluate alignment with future urban extensions.

Results:

The evaluation reveals that 42% of the study area demonstrates high suitability for solar PV, while 35% features moderate to high suitability for onshore wind energy. The combined “High Suitable for Solar & Wind” hybrid category covers 15.2% (10,920 km2) of the region.

Discussion:

The proposed GIS-AHP framework provides a practical tool for early-stage renewable energy site selection. By integrating spatial interaction analysis with proposed urban growth zones, this approach enables planners to balance future population growth and infrastructure demands with optimal clean energy deployment in arid environments.

1 Introduction

Urban expansion in arid regions is rapidly reshaping the relationship between land development, infrastructure provision, and energy demand. In these environments, cities often expand across vast territories where land appears physically available. However, development decisions remain strictly constrained by environmental sensitivity, infrastructure accessibility, land-use conflicts, and long-term energy security. Therefore, renewable energy planning can no longer be treated as an isolated technical exercise concerned solely with identifying areas of high solar irradiance or favorable wind conditions. Instead, it must be examined as an integral component of broader spatial planning, where energy potential, land-use compatibility, infrastructure networks, and future urban growth trajectories (Malczewski, 2006), (Alqurashi et al., 2016).

This challenge is highly relevant to Saudi Arabia, where rapid urban growth aligns with national priorities for energy diversification, environmental sustainability, and low-carbon development under Saudi Vision 2030 (Islam and Ali, 2024), (Alotaibi et al., 2026). The Al-Qassim region represents a rapidly developing arid environment characterized by high solar irradiance, moderate wind potential, and expanding urban corridors, particularly around the Buraydah–Onaizah conurbation. However, favorable resource availability does not automatically translate into effective regional integration. Assessing renewable energy suitability independently from urban expansion and infrastructure constraints can lead to spatial mismatches. Such isolated decisions may identify technically viable locations that are disconnected from future demand, costly to integrate into existing grids, or incompatible with long-term urban growth (Aman et al., 2013, Aydin et al., 2013, Malczewski, 2006). Geographic Information Systems (GIS) combined with Multi-Criteria Decision-Making (MCDM) techniques have been widely utilized to support site suitability analysis. Among these methods, the Analytic Hierarchy Process (AHP) is commonly applied to weight diverse climatic, topographic, environmental, and infrastructural criteria within a spatial framework (Ali et al., 2017), (Elboshy et al., 2022). Previous studies have successfully implemented GIS–MCDM approaches to identify suitable locations for solar, wind, and hybrid systems in various regional contexts, including Turkey, South Korea, Thailand, and Morocco (Aydin et al., 2013), (Ali et al., 2017), (Ali et al., 2022), (Villacreses et al., 2017), (Tazi et al., 2018), (Ezz et al., 2022). These contributions have significantly advanced the technical assessment of renewable energy potential by overlaying resource availability with physical and environmental constraints.

Recent geospatial suitability research has also illustrated that GIS multi-criteria approaches are also flexible and that there are alternatives that rely more on data (Rana and Moniruzzaman, 2023a). used GIS–remote sensing–AHP based MCDM for combining multiple environmental and accessibility criteria for identifying suitable locations for livestock production suitability, and (Rana and Moniruzzaman, 2023b) used the same MCDM framework for identifying the suitability of rainwater-harvesting structures based on multiple environmental and accessibility criteria. In the renewable-energy field (Rana and Moniruzzaman, 2024), used a GIS–AHP approach with nine climatic, topographic, environmental and accessibility factors to identify potential areas for solar PV development in Bangladesh, highlighting the ongoing role of GIS–AHP in enabling clear spatial screening. Recently (Rana et al., 2025), extended the conventional suitability assessment by using AHP–MCAs, where they used machine-learning algorithms such as Random Forest, Extreme Gradient Boosting, and Naïve Bayes, and quantitatively evaluated the performance of the models through independent inventory data and ROC–AUC analysis. All these studies suggest the methodologic progression from expert weighted GIS–AHP and MCDM framework to data driven and hybrid modelling which can mitigate the use of subjective weighting and enhance the predictive validation. However, these sophisticated methods tend to rely on relatively large and stable training and validation sets and GIS–AHP is especially useful for transparent regional scale planning in which multiple and conflicting spatial criteria need to be combined, and empirical inventories of sites are scarce. Another challenge exists in the renewable-energy planning community in the relationship between separately modeled solar suitability, spatial complementarity of solar and wind resources, and planned urban growth in a common spatial decision-support system.

Despite these advancements, critical gaps remain in the existing literature. First, many spatial suitability studies rely primarily on static indicators or long-term average resource values (Aydin et al., 2013), (Elboshy et al., 2022) (Malczewski, 2006), (Charabi and Gastli, 2011). While useful for macro-screening, these approaches often provide limited insight into the spatial co-location of suitable solar PV and wind resources (Kamati et al., 2022), (Mbufua et al., 2025), This constraint is particularly important for hybrid solar–wind energy systems, where planning suitability depends on the combined spatial presence of favorable solar and wind conditions. Second, renewable energy suitability is frequently treated as an isolated optimization problem, offering limited integration with urban growth planning and infrastructure corridors (Alqurashi et al., 2016), (Asadi et al., 2023), (Rana et al., 2025). Third, while recent literature has advanced GIS-based resource modeling, its application as a coordinated tool within future urban growth planning remains insufficiently developed.

Using GIS-based suitability modeling and spatial integration analysis of solar and wind energy, recent research has sought to improve renewable energy planning. However, most of these efforts remain limited to technical feasibility or the optimization of local resource use (Alqurashi et al., 2016), (Elboshy et al., 2022), (Charabi and Gastli, 2011). Less attention has been given to how renewable energy planning can be coordinated with planned urban expansion and infrastructure accessibility within a comprehensive spatial planning approach (Aljaddani et al., 2022), (Guo et al., 2020). In arid regions, bridging this gap is crucial, as vast undeveloped areas offer strategic opportunities to align energy infrastructure with urban growth. In these contexts, the planning value of a site depends not only on resource availability, but also on its potential to reduce land-use conflicts and improve infrastructure efficiency (Aljaddani et al., 2022)– (Alahmadi and Atkinson, 2019).

To bridge this gap, this study developed a spatial framework based on geographic information systems and the analytical hierarchy methodology to assess the suitability of solar photovoltaic energy, onshore wind energy, and solar-wind hybrid energy (

Aydin et al., 2013

) (

Malczewski, 2006

), (

Asadi et al., 2023

), and to study their spatial interaction with urban expansion patterns in Al-Qassim, Saudi Arabia (

Ali et al., 2022

), (

Aljaddani et al., 2022

). The framework develops independent spatial models for solar PV and wind energy, while incorporating planned urban expansion zones as a post-modeling spatial interaction layer (

Aljaddani et al., 2022

), (

Guo et al., 2020

). Additionally, the spatial coincidence between suitable solar PV and onshore wind zones is examined to provide a planning-oriented interpretation of hybrid renewable energy potential. Unlike conventional static site selection, this approach directly links energy resource dynamics with land-use compatibility and planned urban growth (

Aljaddani et al., 2022

). The novelty of this study lies in reframing renewable energy suitability assessment as an urban planning and spatial decision-making problem rather than a purely technical site-selection task. The study makes three primary contributions.

  • It develops an integrated GIS–AHP framework tailored for evaluating regional solar, wind, and hybrid resource suitability in an arid context.

  • It incorporates solar–wind spatial complementarity as an analytical indicator for identifying potential hybrid renewable energy zones.

  • It identifies the spatial intersection between high-priority energy suitability zones and proposed urban expansion zones, thereby linking resource assessment to early-stage, planning-oriented decision-making.

Accordingly, the aim of this study is to implement this integrated framework to identify suitable areas for solar, wind, and hybrid systems, and to evaluate their spatial alignment with urban expansion patterns in Al-Qassim. These findings are intended to support evidence-based spatial decision-making in arid regions where renewable energy infrastructure and urban growth must be planned in a coordinated, sustainable manner.

2 Materials and methods

This study used a GIS–AHP approach to assess renewable energy suitability in Al-Qassim, Saudi Arabia, and to examine its relationship with urban expansion (Aydin et al., 2013), (Elboshy et al., 2022), (Malczewski, 2006). The analysis focused on solar PV, onshore wind, and hybrid solar–wind systems.

In this study, two different suitability models have been established. The first model evaluated solar PV suitability using 13 criteria, while the second model evaluated 12 criteria for onshore wind suitability. This separation was necessary because solar PV and wind energy systems are governed by different technical and spatial constraints (Ali et al., 2017), (Villacreses et al., 2017). Only the solar PV model contained criteria on solar irradiance, ambient temperature, slope, aspect, environmental constraints, and accessibility to infrastructure (Hassaan, 2015), (Hassaan et al., 2021). The wind model contained variables pertaining to wind speed, air density, slope, environmental constraints, and accessibility to infrastructure (Ali et al., 2017), (Barzehkar et al., 2021).

The outputs of the solar PV and wind energy suitability models were combined to create a hybrid suitability model (Mbufua et al., 2025), (Asadi et al., 2023). This integration was used to identify areas where conditions are highly favorable for both energy sources.

Suitability maps for solar PV, wind, and hybrid installations were produced and overlaid on the proposed urban expansion areas (Guo et al., 2020), (Alahmadi and Atkinson, 2019). They were not included as weighted criteria in the Analytic Hierarchy Process (AHP) model. Rather, they were employed in a post-modeling spatial interaction analysis to determine the areas of greatest overlap between future urban growth areas and the optimal sites generated for renewable energy development. This allows for evaluating the spatial relationship (i.e., proximity) between renewable energy potential and areas of planned urban growth separately from the assessment of suitability for urban expansion.

The methodology included six sequential phases: data collection, data preparation, criteria reclassification, AHP weighting, suitability mapping and hybrid assessment, and spatial interaction analysis. Three analyses were conducted to check the model outputs. The first involved verifying the consistency of the Analytic Hierarchy Process (AHP) (Saaty, 1987). The second involved adjusting the weights of selected criteria to assess sensitivity. The third involved comparing the suitable areas with existing renewable energy sites and known high-potential areas.

2.1 Study area

Al-Qassim is situated in the central part of Saudi Arabia (Qassim University, 2026), extending between latitudes 24°30′–28°30′N and longitudes 41°30′–45°00′E (Figure 1). The study area calculated through the GIS-derived study area was approximately 72,000 km2, derived from the official administrative boundary layer selected for this investigation. It is bordered by Riyadh to the south and east, Hail to the north, and Madinah to the west. Buraydah serves as the regional capital, while Onaizah and other surrounding towns constitute a significant, continuous urban corridor in the region.

FIGURE 1

The Al-Qassim region is classified as having an arid desert climate according to the Köppen-Geiger climate classification (Beck et al., 2023). It is characterized by hot summers and mild to warm winters, with low annual rainfall and consistently high solar irradiance. These prevailing climatic conditions make solar PV energy one of the most viable renewable energy sources (Hersbach et al., 2020), (Albraheem and Alabdulkarim, 2021) classified as environmentally sustainable in this region. While onshore wind conditions are more spatially variable, the surrounding hills and plains offer distinct potential for wind energy generation (Alotaibi et al., 2026). This unique combination of solar and wind resources makes the region an ideal case study for examining the feasibility of hybrid solar–wind energy systems (Barzehkar et al., 2021).

Geographically, the Al-Qassim region is characterized by mostly flat to gently sloping terrain, with elevations generally ranging from 600 to 950 m above sea level. Terrain slope, elevation, and aspect have critical relevance to renewable energy planning, as they directly affect construction feasibility, solar exposure, wind behavior, manufacturing processes, and infrastructure costs (Hassaan et al., 2021), (Elboshy et al., 2022), (Charabi and Gastli, 2011). However, physical topography factors are not the only determinants of site suitability. Other critical factors affecting renewable energy deployment include protected areas, flood-prone zones, bird-sensitive areas, water bodies, existing settlements, and accessibility to roads and power lines (Albraheem and Alabdulkarim, 2021), (Albraheem and AlAwlaqi, 2023), (Al Garni and Awasthi, 2017).

Al-Qassim represents a valuable study site as it balances high renewable energy potential with active urban growth. Major urban expansions are concentrated within large cities like Buraydah and Onaizah, alongside the smaller settlements surrounding them, whereas the vast outlying areas are characterized by lower urban density. These distinct spatial patterns facilitate the analysis of whether highly suitable renewable energy zones structurally align with areas targeted for future urban expansion. Consequently, this study utilizes Al-Qassim to implement a planning-oriented GIS–AHP approach for the suitability evaluation of solar PV, onshore wind, and hybrid solar–wind energy, combining resource potential with land-use compatibility, infrastructure accessibility, environmental constraints, and proposed urban expansion areas (Aydin et al., 2013), (Asadi et al., 2023).

2.2 Methodology

The methodology focused on determining the suitability of renewable energy and studying its relationship to specific urban expansion areas. Separate suitability models for solar photovoltaic and onshore wind energy were analyzed within a geographic information system (GIS) environment. The two models were then combined to develop a hybrid suitability map for solar and wind energy (Saaty, 1977).

The systematic workflow process includes six basic steps, the first four of which focus on data preparation and criteria weighting. First, the necessary spatial datasets encompassing climatic, terrain, environmental, infrastructure, and urban expansion variables were acquired. Second, all spatial layers were harmonized to a consistent coordinate reference system, spatial resolution, and study boundary, thereby enabling seamless comparison and integration during spatial analysis. Third, the suitability scales for both the solar PV and wind models were standardized into a common framework ranging from 1 (not suitable) to 4 (highly suitable), with reclassification rules derived from technology-specific technical requirements and established literature. Fourth, the Analytic Hierarchy Process (AHP) was employed to determine the relative weight of each criterion (Saaty, 2008); given that solar PV and wind models are influenced by distinct factors, they were simulated utilizing distinct AHP weighting schemes.

The consistency ratio was calculated to check the reliability of the pairwise comparisons. Fifth, a weighted overlay analysis was used to generate the solar PV and wind suitability maps. These two outputs were then combined to identify areas suitable for hybrid solar–wind development. This step included an assessment of the spatial coincidence between suitable solar PV and onshore wind zones, supporting the interpretation of the hybrid suitability results. Sixth, the proposals for urban expansion areas were utilized after generating the solar PV, wind, and hybrid suitability maps. Thus, they were not treated as weighted criteria in the AHP model. Rather, they were applied in a post-modeling spatial interaction evaluation to measure the overlap of highly suitable renewable energy zones with areas projected for future urban growth. This separation enabled the evaluation of renewable energy suitability in isolation prior to testing its spatial overlap with planned urban expansion, as shown in Figure 2.

FIGURE 2

2.3 Data collection and criteria selection

This study used spatial datasets to develop suitability models for solar PV and onshore wind energy. The datasets include resource availability, terrain conditions, environmental restrictions, infrastructure accessibility, and urban expansion trends. All data were prepared and processed within a GIS environment (Charabi and Gastli, 2011), (Albraheem and AlAwlaqi, 2023).

The solar PV model incorporates 13 criteria. These factors comprise solar irradiation, ambient temperature, slope, aspect, distance from protected areas, distance from streams, distance from bird migration paths, distance from power lines, distance from roads, distance from railways, distance from airports, distance from water bodies, and distance from cities (Albraheem and Alabdulkarim, 2021), (Al Garni and Awasthi, 2017), (Gasparatos et al., 2017).

There are 12 criteria in the onshore wind model. The variables include wind speed, air density, slope, distance from protected areas, distance from streams, distance from bird migration paths, distance from power lines, distance from roads, distance from railways, distance from airports, distance from water bodies, and distance from cities (Gasparatos et al., 2017).

The AHP models did not use the proposed urban expansion layer as a weighted criterion. Instead, it was applied after generating the suitability maps to assess the overlap between the high renewable energy suitability zones and the areas of planned urban growth.

2.3.1 Data sources

In this study, we collected and processed various spatial and environmental data using the following methods:

The solar PV suitability assessment was carried out using monthly data of PV potential and ambient temperature from the Global Solar Atlas from January to October 2023 (World Bank Group, ESMAP,Solargis, 2019). Thus, the time range of these datasets is January to October 2023, and should not be viewed as a long-term climatological average. Onshore wind resource availability and its influence on turbine performance was evaluated using wind speed and air density data from the Global Wind Atlas (Davis et al., 2023).

Topography & Land Cover: Elevation, slope, and aspect were derived from the SRTM Digital Elevation Model a 30 m spatial resolution (Farr et al., 2007). Land use and land cover data were collected from the Saudi National Spatial Data Infrastructure, categorized according to restricted, urban, and agricultural areas.

Infrastructure and Avoided Areas: Infrastructure layers (roads, railways, transmission lines, airports, and urban centers) along with environmental constraints (protected areas, streams, flood-prone zones, water bodies, and bird-sensitive habitats) were extracted from national and regional spatial databases (G. A. for S. and G. I. GEOSA, 2021). The study also incorporated future urban expansion vectors for the post-modeling spatial interaction analysis.

All collected layers were clipped to the Al-Qassim regional boundary and projected under the same coordinate reference system (WGS 1984 UTM Zone 38N).

2.3.2 Identification of criteria

The criteria were chosen based on former renewable energy suitability studies, the physical environment of Al-Qassim, and their strategic relevance to planning practices (Albraheem and Alabdulkarim, 2021), (Al Garni and Awasthi, 2017). They include considerations of resource availability, terrain conditions, environmental constraints, access to infrastructure, and proximity to urban areas.

Also, the criteria were divided into two groups due to the different technical requirements of photovoltaic solar power systems and onshore wind power systems. Tables 1 and 2 show the criteria used in the suitability models for photovoltaic solar and onshore wind power systems, respectively. Figure 3 illustrates the spatial input layers and the underlying constraints used in the suitability analysis.

TABLE 1

CategoryCriterionData sourceData typeRelevance to solar PV suitability
ClimaticSolar irradiationGlobal solar atlasJanuary–October 2023 dataMain indicator of solar PV potential
ClimaticAmbient temperatureGlobal solar atlasJanuary–October 2023 dataAffects PV system efficiency
TopographicSlopeSRTM DEM30 mAffects installation feasibility and construction cost
TopographicAspectSRTM DEM30 mInfluences solar exposure
EnvironmentalProtected areasNational environmental datasetsVectorAvoids conflict with protected land
EnvironmentalStreamsNational/regional spatial datasetsVector/rasterReduces physical and environmental risk
EnvironmentalBird-sensitive areasEnvironmental datasetsVectorReduces ecological conflict
InfrastructurePower linesNational/regional infrastructure datasetsVectorImproves grid connection potential
InfrastructureRoadsNational/regional infrastructure datasetsVectorImproves site accessibility
InfrastructureRailwayNational/regional infrastructure datasetsVectorRepresents transport accessibility and planning constraints
InfrastructureAirportsNational/regional infrastructure datasetsVectorAvoids safety and land-use conflict
EnvironmentalWater bodiesNational/regional spatial datasetsVector/rasterAvoids unsuitable or restricted areas
Urban-relatedCitiesNational/regional urban datasetsVectorReflects proximity to demand centers and settlement constraints

Solar PV suitability criteria and data sources.

Criteria selection was guided by previous GIS-based solar PV, suitability studies and environmental screening considerations (Gasparatos et al., 2017), (Albraheem and Alabdulkarim, 2021), (Al Garni and Awasthi, 2017).

TABLE 2

CategoryCriterionData sourceData typeRelevance to wind suitability
ClimaticWind speedGlobal wind atlasYearly averageMain indicator of wind energy potential
ClimaticAir densityGlobal wind atlas/climate datasetsYearly averageAffects wind turbine performance
TopographicSlopeSRTM DEM30 mAffects construction feasibility and turbine installation
EnvironmentalProtected areasNational environmental datasetsVectorAvoids conflict with protected land
EnvironmentalStreamsNational/regional spatial datasetsVector/rasterReduces physical and environmental risk
EnvironmentalBird-sensitive areasEnvironmental datasetsVectorReduces ecological conflict and bird collision risk
InfrastructurePower linesNational/regional infrastructure datasetsVectorImproves grid connection potential
InfrastructureRoadsNational/regional infrastructure datasetsVectorImproves site accessibility
InfrastructureRailwayNational/regional infrastructure datasetsVectorRepresents transport accessibility and planning constraints
InfrastructureAirportsNational/regional infrastructure datasetsVectorAvoids safety and aviation-related constraints
EnvironmentalWater bodiesNational/regional spatial datasetsVector/rasterAvoids unsuitable or restricted areas
Urban-relatedCitiesNational/regional urban datasetsVectorReflects proximity to demand centers and settlement constraints

Onshore wind suitability criteria and data sources.

Wind suitability criteria were chosen based on the previous GIS-based wind energy suitability studies, wind energy site selection applications in Saudi Arabia, and ecological screening considerations (Marques et al., 2014), (Albraheem and Almutlaq, 2024).

FIGURE 3

The proposed urban expansion layer was not incorporated as a weighted criterion in the AHP models. Instead, a post-modeling spatial interaction analysis was used to analyze the congruence of planned urban growth with renewable energy suitability.

2.4 Analytic Hierarchy Process (AHP)

Relative weights for the criteria included in the solar PV and wind suitability models were assigned using the Analytic Hierarchy Process (AHP). AHP was chosen because it presents a systematic and structured approach to compare multiple criteria for their relative importance in the spatial-suitability analysis (Saaty, 1977).

AHP matrices were created independently for the solar PV and wind turbine systems. This was required since diverse renewable energy systems are impacted by various factors. By contrast, the solar PV model used only solar irradiation as a resource factor. Wind speed was the only resource factor included in the wind model.

The pairwise-comparison matrices were normalized to obtain the priority vector and the final weight of each indicator. Two separate matrices have been created for the solar PV and onshore wind models due to the different technical and spatial factors affecting the two energy systems. The solar PV model consisted of 13 criteria and thus had a 13 x 13 pairwise comparison matrix, while the onshore wind model consisted of 12 criteria and thus a 12 x 12 pairwise comparison matrix. To be transparent and reproducible in the method, the full pairwise comparison matrices are given in Appendix at the end of the manuscript. After normalization, the consistency of each matrix was checked by the maximum eigenvalue (λmax), CI, RI and CR as per AHP consistency procedure by Saaty and reporting process of (Rana et al., 2022), Equations 1 and 2.where (CI) is the consistency index, λmax is the maximum eigenvalue of the pairwise comparison matrix, and (n) is the number of criteria.

The consistency ratio was calculated using Equation 2where (CR) is the consistency ratio and (RI) is the random index corresponding to matrix size. A (CR) value of ≤ 0.10 was considered acceptable.

In the case of the solar PV model, the highest weights were assigned to solar irradiation and ambient temperature, followed by aspect, slope, and distance to power lines. Criteria such as solar resource availability, PV efficiency, terrain factors, and grid accessibility play a key role in this weighting scheme.

For the wind model, wind speed and air density received the greatest weights. Subsequent factors taken into account were slope and proximity to power lines. These criteria are strictly based on factors such as wind resource availability, turbine performance, topography, and grid connection parameters.

The remaining criteria were assigned lower weights in both models. These factors primarily concern environmental constraints, accessibility conditions, and land-use compatibility. The hierarchical analysis model was not weighted to account for the proposed urban expansion; instead, a post-modeling spatial interaction analysis was conducted for each model using the layer representing the proposed urban expansion.

The final AHP weights were used in the GIS weighted overlay analysis to generate suitability maps for solar PV and onshore wind. The AHP weights for the solar PV and wind models are listed in Tables 3, 4.

TABLE 3

CategoryCriterionPriority weight (%)Rank
ClimaticSolar irradiation27.41
ClimaticAmbient temperature17.32
TopographicAspect11.93
TopographicSlope8.24
InfrastructurePower lines8.25
EnvironmentalProtected areas6.46
EnvironmentalStreams4.87
InfrastructureRoads3.48
InfrastructureRailway3.49
EnvironmentalWater bodies3.110
Urban-relatedCities2.411
InfrastructureAirports212
EnvironmentalBird-sensitive areas1.513

AHP weights for the solar PV suitability model.

TABLE 4

CategoryCriterionPriority weight (%)Rank
ClimaticWind speed23.31
ClimaticAir density18.12
TopographicSlope12.03
InfrastructurePower lines10.04
EnvironmentalProtected areas9.35
EnvironmentalStreams6.76
InfrastructureRailway4.67
InfrastructureRoads4.58
Urban-relatedCities3.29
EnvironmentalWater bodies3.210
InfrastructureAirports3.111
EnvironmentalBird emigration path2.012

AHP weights for the onshore wind-suitability model.

2.5 Criteria reclassification and Weighted Overlay analysis

Once the AHP weights were assigned, each criterion was recategorized into a common suitability scale. This scale ranges from 1 (unsuitable areas) to 4 (highly suitable areas). This task was necessary since the input layers had different units and value ranges. Reclassification rules were defined according to the technical requirements of each energy system and previous suitability studies (Malczewski, 2006). In terms of the solar PV model, suitability increased with increasing solar irradiation, lower ambient temperatures, gentler slopes, favorable aspects, and appropriate distances from environmental and infrastructure constraints. Within the wind model, higher suitability was aligned with increasing wind speeds and air densities, lower slope values, and safe distances away from environmental and infrastructure constraints.

Weighted overlay analysis was conducted independently for the solar PV and wind models. Using the AHP weights, the reclassified score for each criterion within a grid cell was multiplied by its corresponding weight. These weighted scores were then summed to produce a final suitability score for each pixel.

The final suitability score was calculated using Equation 3.where S is the final suitability score, Wi is the AHP weight of criterion i, Xi is the reclassified suitability score of criteria i, and n is the total number of criteria.

Equation 3 was applied separately to the solar PV and wind criteria. This produced two spatial outputs: a solar PV suitability map and an onshore wind suitability map. These maps were classified into four suitability classes: unsuitable, low, moderate, and high. These data were then used as the main inputs for the hybrid solar–wind suitability assessment.

2.6 Hybrid solar–wind suitability assessment

The hybrid solar–wind suitability assessment was performed after generating the individual solar PV and onshore wind suitability maps. This step was used to determine the spatial suitability of co-located renewable energy resources. The purpose was not only to create a composite map, but also to consider the strategic potential for hybrid renewable energy projects compared with single-resource installations (Asadi et al., 2023).

The final suitability scores for solar PV and wind were integrated within the GIS environment. This integration enabled the results of the two individual models to be combined for the purpose of computing the hybrid assessment, instead of re-running the original input criteria. High suitability scores in both models were deemed most suitable for hybrid solar–wind development.

The Hybrid suitability assessment was segmented into the following combined categories based on the spatial relationship between solar PV suitability output and wind suitability output: High Suitable for Solar & Wind, High Suitable for Solar Only, High Suitable for Wind Only, Moderate Suitable for Solar & Wind, Low Suitable for Solar & Wind, and Unsuitable for Solar & Wind. These categories were employed to delineate those locations that are more suitable for co-located hybrid development from those that are more suited for one renewable-energy technology development.

The results of the hybrid suitability model were used as an analytical layer in subsequent stages. These results were interpreted by examining the convergence of photovoltaic solar and wind energy potentials. Their spatial suitability was also assessed according to the projected pattern of future urban expansion, using the areas proposed for this purpose.

2.7 Solar–wind spatial complementarity assessment

Solar–wind spatial complementarity was assessed to identify areas where suitable solar PV and onshore wind conditions occur together. This step was used to support the interpretation of the hybrid solar–wind suitability results.

The assessment was based on the final solar PV and wind suitability outputs. These outputs were overlaid in the GIS environment to identify areas where high solar PV suitability coincided with high wind suitability. Areas showing favorable suitability in both models were considered more relevant for hybrid solar–wind planning (Jurasz et al., 2020).

2.8 Spatial interaction analysis with urban expansion

A spatial interaction analysis was performed to examine the relationship between proposed urban expansion areas and renewable energy suitability. This step was conducted after generating the solar PV, wind, and hybrid suitability maps. The proposed urban expansion layer was treated as an independent planning layer and was not included as a weighted criterion in the AHP models. This separation enabled the analysis of renewable energy potential independently before examining its spatial alignment against planned urban development (Aljaddani et al., 2022), (Guo et al., 2020).

Areas where urban expansion zones overlap with areas of high suitability for renewable energy were analyzed. High suitability categories for solar photovoltaic, wind, and hybrid systems were extracted from the GIS environment and then integrated with the urban expansion layer. The total overlap area was then calculated to represent the extent to which future urban development overlaps with optimal renewable energy zones, thereby assessing the spatial compatibility between the potential of various renewable energy forms and their planned locations.

This analysis concludes by supporting a planning-based interpretation. In particular, areas with high suitability for renewable energy and overlap with proposed urban expansion would provide priority target areas in the development of integrated land use planning. Conversely, low spatial overlap may require additional infrastructure planning, alternative land-use allocation, or future investment to connect suitable renewable energy zones with urban expansion areas.

3 Results

This section examines the suitability of solar photovoltaic (PV), onshore wind, and hybrid solar–wind energy in Al-Qassim. It also illustrates the solar–wind spatial complementarity pattern and the spatial overlap with proposed urban expansion zones. The results are presented in the following order: individual resource suitability, hybrid energy suitability, spatial complementarity, and planning implications.

3.1 Solar PV suitability

The solar PV suitability map shows that the high-suitability class covers about 42% of the study area, mostly in the northern and western parts of Al-Qassim (Figure 4). This distribution matches areas with high solar irradiation, low elevation, and fewer land-use restrictions. In contrast, the main urban and agricultural corridor especially around Buraydah and Onaizah shows lower suitability because existing infrastructure and land competition limit large-scale projects. Ultimately, these results show that Al-Qassim has significant spatial potential, making the high-suitability zones an essential baseline for future solar energy planning.

FIGURE 4

3.2 Onshore wind suitability

The wind suitability map shows that the moderate and high suitability classes occupy about 35% of the study area, mostly in the western plateau and northern regions of Al-Qassim (Figure 5). Generally, these areas have wind velocities higher than 6.5 m/s, good land form, open terrain, more wind exposure and less physical obstruction.

FIGURE 5

The central urban corridor around Buraydah and Onaizah has lower wind suitability due to lower average wind speed and high population density and mixed use. Environmental and topographic factors also make less suitable the areas in the south and in the east. In summary, the suitability of wind is more geographically constrained than the suitability of solar PV, but moderate- and high-suitability areas are still relevant for hybrid solar–wind planning.

3.3 Hybrid solar–wind suitability

The hybrid solar–wind suitability map has been produced to show the spatial relationship between solar PV suitability and onshore wind suitability, and is summarized in Table 5. The High Suitable for Solar & Wind category represents the priority areas for hybrid renewable energy development and accounts for 10,920 km2 or 15.2% of the study area. High Suitable for Solar Only areas make up 12,960 km2 (18.0%) and High Suitable for Wind Only areas comprise 6,480 km2 (9.0%). Moderate Suitable for Solar & Wind is 19,440 km2 (27.0%) while Low Suitable for Solar & Wind is 10,800 km2 (15.0%) and Unsuitable for Solar & Wind is 11,400 km2 (15.8%). The results suggest that the spatial selectivity of the best development areas for hybrid is higher than that of the best development areas for a single renewable-energy technology.

TABLE 5

Suitability classArea (km2)Area (%)Description
High suitable for solar & wind10,92015.2%Solar photovoltaic and onshore wind energy resources are highly suitable in the same priority areas. These areas are ideal locations for hybrid renewable energy
High suitable for solar only12,96018.0%These areas are characterized by moderate to light winds, making them suitable for photovoltaic solar power systems. These areas are suitable for solar power systems only and may not be ideal for hybrid systems
High suitable for wind only6,4809.0%Onshore wind power is highly suitable, while the suitability of solar photovoltaic power ranges from moderate to low in some areas. These areas are primarily suited to wind power, but not as well to hybrid solar and wind power systems integrated into the same site
Moderate suitable for solar & wind19,44027.0%Areas with moderate suitability for both solar and wind energy resources. These areas can be developed in a hybrid manner, although not as high a priority as areas with high suitability
Low suitable for solar & wind10,80015.0%Areas with low suitability for both resources. Generally, these areas should not be used for renewable energy projects without further evaluation
Unsuitable for solar & wind11,40015.8%Areas where renewable energy cannot be developed due to environmental, topographical and/or infrastructure constraints
Total72,000100%—

Spatial distribution of hybrid solar–wind suitability classes.

3.4 Spatial interaction with urban expansion

The spatial interaction analysis indicated that the spatial interaction analysis indicated that proposed urban expansion areas overlap with high-suitability renewable-energy zones. High suitability renewable-energy areas, particularly solar PV, heavily overlapped urban development areas, with about 18%–20% of the urban development area proposed for development in these high suitability areas. The overlap was limited primarily in the main urban corridor of Buraydah, Onaizah and the surrounding villages. These are locations that are experiencing development pressure, have access to infrastructure, and have favorable conditions for renewable energy.

Areas outside the proposed urban expansion areas were also identified as having high suitability for renewable energy. These areas would hold true for larger scale utility projects but may need to be planned individually for connection to the grid, land planning and supporting infrastructure. On the whole, the spatial interaction results suggest opportunities for planning for coordinated renewable-energy and urban-growth development and a potential for future urban-growth and renewable-energy competition.

3.5 Model checking results

To quantitatively validate the results, the location of the existing solar PV project that was verified as shown in Figure 6. The four solar plants in Al Qassim are shown in Figures 6a and the evidence that the plant location is site in the high suitability zone are shown in Figures 6b-c and 7-day. The model checking results are summarized in Table 6. The consistency ratios were 0.0094 for the solar PV model and 0.0083 for the onshore wind model. Both values were well below the acceptable threshold of 0.10, indicating satisfactory consistency of the pairwise comparisons. Furthermore, the sensitivity analysis showed limited variance in the final fit outputs, with the change in fit ranking not exceeding 2.8% after adjusting the weights of the selected criteria. This demonstrates that the main spatial patterns were not significantly affected by the small changes in weights.

FIGURE 6

TABLE 6

CheckResultInterpretation
Solar PV AHP consistency ratio0.0094The values of the pairwise comparisons were within acceptable limits (CR ≤ 0.10)
Onshore wind AHP consistency ratio0.0083The values of the pairwise comparisons were within acceptable limits (CR ≤ 0.10)
Quantitative spatial validation4 of 4 existing solar PV projects (100%) located in the high-suitability classThe existing solar PV project location are spatially consistent with the modeled high-suitability area
Sensitivity variation2.8%The main suitability classes changed only slightly after weight adjustment

Model checking results.

The four locations of the existing solar PV projects were used for quantitative spatial validation as shown in Figure 6. The four project locations were all in the high-suitability (4 of 4; 100%) class of the solar PV suitability map. This spatial agreement is quantitative support for the solar PV suitability model. The results should be interpreted as a guide only, however, as the sample of projects for validation is only four. No documented projects of wind or hybrid projects were present in the study area to make project based quantitative validation for these models.

4 Discussion

The results indicate that renewable energy suitability in Al-Qassim is shaped by more than resource availability. Terrain conditions, land-use constraints, infrastructure access, and proposed urban expansion patterns also influence the spatial distribution of suitable areas. This supports the need to examine renewable energy planning as part of spatial planning, rather than as a separate technical site-selection task (Guo et al., 2020).

4.1 Interpretation of solar and wind energy potential

The results show that solar PV suitability is spatially broader than onshore wind suitability. The high solar PV suitability class covers a large share of the study area, especially in the northern and western parts of Al-Qassim. This pattern reflects the advantage of arid environments, where high solar exposure, open land, and relatively simple terrain conditions support PV deployment. Previous GIS-based solar suitability studies in Saudi Arabia have also identified solar radiation, slope, aspect, and infrastructure accessibility as important determinants of PV suitability (Albraheem and AlAwlaqi, 2023), (Al Garni and Awasthi, 2017).

In contrast, onshore wind suitability shows a more selective spatial pattern. Moderate and high wind suitability zones are mainly concentrated in the western plateau and northern parts of the region. This reflects the higher spatial variability of wind resources compared with solar resources. Wind suitability is also more sensitive to terrain exposure, wind speed distribution, and local topographic conditions. This agrees with wind-energy site-selection work in Saudi Arabia, where suitable wind zones were found to be more spatially concentrated and strongly controlled by wind resource availability and terrain conditions (Albraheem and AlAwlaqi, 2023).

The lower suitability observed along the central urban and agricultural corridor around Buraydah and Onaizah indicates that land-use competition can reduce the practical suitability of renewable energy sites, even where resource conditions are acceptable. This finding is important for regional planning because it shows that technically suitable areas may not always be planning-compatible when existing settlements, agriculture, infrastructure networks, and future expansion pressures are considered.

4.2 Hybrid Suitability and spatial complementarity

The hybrid solar–wind suitability results show that the highest-priority zones are more spatially selective than solar PV zones alone (Figure 7). This indicates that hybrid renewable energy planning should not be treated as a direct extension of solar PV planning. Hybrid suitability depends on the spatial coincidence of suitable solar and wind conditions, as well as the compatibility of terrain, environmental constraints, and infrastructure access. This is consistent with the concept of renewable energy complementarity, where combined resource planning can improve spatial and operational suitability compared with single-resource assessment (Asadi et al., 2023), (Jurasz et al., 2020).

FIGURE 7

The High Suitable for Solar & Wind areas represent priority areas where both solar PV and onshore wind resources can be considered together under favorable spatial conditions. These areas are important because they may support more diversified renewable energy planning and reduce dependence on a single resource type. However, the more limited extent of High Suitable for Solar & Wind category also indicates that hybrid development requires more selective spatial planning than solar PV development alone.

4.3 Spatial alignment with urban expansion

The spatial interaction analysis shows that part of the proposed urban expansion areas overlaps with high renewable energy suitability zones. This overlap is greatest for solar PV suitability, followed by hybrid solar–wind suitability. This finding has two planning implications.

First, some future urban growth areas may provide opportunities for integrating renewable energy planning into urban development. Such areas could support local renewable energy projects, energy-related infrastructure, or utility corridors near future demand centers. This may reduce the spatial distance between electricity generation and urban energy demand and support more coordinated infrastructure planning.

Second, overlap between renewable energy suitability and urban expansion may also create potential land-use conflicts. Areas suitable for renewable energy may compete with future housing, services, agriculture, transport infrastructure, or other urban land requirements. Therefore, renewable energy deployment areas should be considered at an early stage together with urban land-use planning (Guo et al., 2020), (Kamati et al., 2022). In this context, the proposed GIS–AHP framework can help identify potential spatial conflicts before final development decisions are made.

High-suitability renewable energy areas located outside the proposed urban expansion zones are also valuable. These areas may be more appropriate for larger utility-scale projects, but they may require separate planning for grid connection, road access, land allocation, and infrastructure investment. This distinction helps differentiate between areas that may support local urban-energy integration and areas that may be more suitable for regional-scale renewable energy development.

4.4 Contribution to arid urban planning

The main contribution of this study is that it reframes renewable energy suitability assessment as a planning-oriented spatial decision problem. Many renewable energy suitability studies focus mainly on identifying suitable land for solar and/or wind development (Albraheem and AlAwlaqi, 2023), (Al Garni and Awasthi, 2017). This study extends that approach by integrating three components within a single GIS–AHP framework: solar PV suitability, onshore wind suitability, and spatial interaction with proposed urban expansion.

This is important because land availability in arid regions can be misleading. Large open spaces may initially appear suitable for renewable energy projects, but their actual planning value depends on infrastructure access, environmental restrictions, land-use competition, and future urban growth (Guo et al., 2020), (Albraheem and Almutlaq, 2024). By integrating these dimensions, the proposed framework provides a clearer basis for identifying where renewable energy development can support urban growth, where it may conflict with future land demand, and where additional infrastructure planning may be required.

The framework can support early-stage decision-making by municipalities and regional planning authorities. It helps identify priority areas for solar PV, onshore wind, and hybrid solar–wind development while also comparing these areas with future urban expansion plans. This makes the approach relevant for arid and semi-arid regions where energy demand is growing, urban expansion is continuing, and land-use decisions need to support long-term sustainability.

The proposed methodology can also be adapted to other regions. However, the criteria, weights, and suitability thresholds should be adjusted to local conditions because resource patterns, infrastructure networks, environmental limitations, and urban growth pressures vary across regions.

4.5 Study limitations and future research

There are several important limitations to this study. First, the suitability outputs depend on the spatial accuracy, availability, and uncertainty of the input data. While this data is suitable for regional planning, more spatially accurate information on land use, infrastructure, and meteorology would be useful for site-level assessments. Furthermore, the suitability categories selected through reclassification thresholds may affect the geographic scope of these categories and should therefore be adjusted to reflect the local context.

Second, assessing the consistency of pairwise comparisons does not guarantee the objectivity of the AHP weighting process, as it relies on expert opinion. The results of this study can be compared with other methods, such as fuzzy AHP, TOPSIS, machine learning, or other hybrid MCDM approaches, in future studies.

Third, solar and wind resource data are not necessarily available or accurate for short time scales or seasonality. Longer term and higher temporal resolution time-series data, power generation simulation and storage requirements could be added in future studies.

Finally, the study lacked detailed network capacity and connection data for the project, a comprehensive economic feasibility study, and a thorough field verification. Therefore, land costs, network connection costs, construction costs, and operating costs, as well as investment viability, should be considered before project implementation. Further research is also required, including a detailed network analysis and additional field or operational verifications.

5 Conclusion

This study demonstrates that combining GIS with the AHP approach can provide a useful planning tool for regional-scale renewable energy assessment. The proposed framework integrates spatial suitability modeling, solar–wind spatial complementarity, and urban expansion analysis. The findings indicate that solar PV has broad spatial potential in Al-Qassim, whereas onshore wind suitability is more spatially selective. Therefore, effective hybrid solar–wind development depends not only on the availability of individual resources, but also on the spatial coincidence of suitable solar PV and wind conditions.

The identified high-suitability energy zones often overlap with proposed urban growth corridors, providing opportunities for local renewable energy integration. At the same time, this overlap may also indicate future land-use competition with housing, agriculture, services, and infrastructure expansion.

In summary, the proposed framework provides regional authorities with a practical decision-support tool for planning renewable energy development in arid environments. At the project level, further assessment of grid constraints, land ownership, land cost, and implementation conditions would be required. However, the methodology provides a useful foundation for balancing renewable energy potential with long-term urban sustainability.

Statements

Data availability statement

The original contributions presented in the study are included in the article/Supplementary Material, further inquiries can be directed to the corresponding author.

Author contributions

ME: Formal Analysis, Supervision, Software, Data curation, Writing – original draft, Project administration, Visualization, Investigation, Resources, Validation, Conceptualization, Writing – review and editing, Methodology. AS: Writing – original draft, Project administration, Conceptualization, Methodology, Visualization, Funding acquisition, Supervision. DS: Supervision, Conceptualization, Writing – original draft, Software, Writing – review and editing, Formal Analysis, Project administration, Resources, Data curation. HY: Writing – original draft, Investigation, Formal Analysis, Visualization, Resources, Methodology, Writing – review and editing. MA: Writing – review and editing, Methodology, Writing – original draft, Investigation, Project administration, Resources. RK: Methodology, Resources, Writing – original draft, Visualization, Writing – review and editing, Formal Analysis.

Funding

The author(s) declared that financial support was received for this work and/or its publication. This work was partially funded by Kingdom University, Kingdom of Bahrain, under Research Grant No. KU–2025–2026–01.

Acknowledgments

The authors would like to express their sincere appreciation to Kingdom University, Kingdom of Bahrain, for its financial and technical support. The authors also extend their gratitude to Unaizah Colleges and the Research Center of Unaizah Colleges for their valuable academic and research support.

Conflict of interest

The author(s) declared that this work was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest.

Generative AI statement

The author(s) declared that generative AI was not used in the creation of this manuscript.

Any alternative text (alt text) provided alongside figures in this article has been generated by Frontiers with the support of artificial intelligence and reasonable efforts have been made to ensure accuracy, including review by the authors wherever possible. If you identify any issues, please contact us.

Publisher’s note

All claims expressed in this article are solely those of the authors and do not necessarily represent those of their affiliated organizations, or those of the publisher, the editors and the reviewers. Any product that may be evaluated in this article, or claim that may be made by its manufacturer, is not guaranteed or endorsed by the publisher.

Supplementary material

The Supplementary Material for this article can be found online at: https://www.frontiersin.org/articles/10.3389/fbuil.2026.1959364/full#supplementary-material

Abbreviations

GIS, Geographic Information System; MCDM, Multi-Criteria Decision-Making; MCDA, Multi-Criteria Decision Analysis; AHP, Analytic Hierarchy Process; PV, Photovoltaic; WT, Wind Turbine; PV–WT, Hybrid Photovoltaic–Wind Turbine System; GHI, Global Horizontal Irradiance; DEM, Digital Elevation Model; LULC, Land Use/Land Cover; ERA5, ECMWF Reanalysis 5 Dataset; ECMWF, European Centre for Medium-Range Weather Forecasts; SRTM, Shuttle Radar Topography Mission; NSDI, National Spatial Data Infrastructure; MoMRA, Ministry of Municipal and Rural Affairs; SEC, Saudi Electricity Company; SWA, Saudi Wildlife Authority; NCEC, National Center for Environmental Compliance; WLC, Weighted Linear Combination; CR, Consistency Ratio; BIPV, Building-Integrated Photovoltaics; UTM, Universal Transverse Mercator.

References

  • 1

    Al GarniH. Z.AwasthiA. (2017). Solar PV power plant site selection using a GIS-AHP based approach with application in Saudi Arabia. Appl. Energy206, 1225–1240. 10.1016/j.apenergy.2017.10.024

  • 2

    AlahmadiM.AtkinsonP. M. (2019). Three-fold urban expansion in Saudi Arabia from 1992 to 2013 observed using calibrated DMSP-OLS night-time lights imagery. Remote Sens.11 (19), 2266. 10.3390/rs11192266

  • 3

    AlbraheemL.AlabdulkarimL. (2021). Geospatial analysis of solar energy in Riyadh using a GIS-AHP-bASED tECHNIQUE. ISPRS Int. J. Geo-Information10 (5), 291. 10.3390/ijgi10050291

  • 4

    AlbraheemL.AlAwlaqiL. (2023). Geospatial analysis of wind energy plant in Saudi Arabia using a GIS-AHP technique. Energy Rep.9, 5878–5898. 10.1016/j.egyr.2023.05.032

  • 5

    AlbraheemL.AlmutlaqF. (2024). A geographic information system-based model and analytic hierarchy process for wind farm site selection in the Red Sea. ISPRS Int. J. Geo-Information13 (11), 416. 10.3390/ijgi13110416

  • 6

    AliS.LeeS.JangC. (2017). Determination of the Most optimal On-Shore wind farm site location using a GIS-MCDM methodology: evaluating the case of South Korea. Energies10 (12), 2072. 10.3390/en10122072

  • 7

    AliF.BennuiA.ChowdhuryS.TechatoK. (2022). Suitable site selection for solar-based green hydrogen in southern Thailand using GIS-MCDM approach. Sustainability14 (11), 6597. 10.3390/su14116597

  • 8

    AljaddaniA. H.SongX. P.ZhuZ. (2022). Characterizing the patterns and trends of urban growth in saudi arabia’s 13 capital cities using a landsat time series. Remote Sens.14 (10), 2382. 10.3390/rs14102382

  • 9

    AlotaibiM. A.AlmubarakY. H.AlguhiA. A. (2026). Multi-criteria decision-making approach for optimizing solar pv farms locations in Saudi Arabia with techno-economic considerations. Energy Rep.15, 109113. 10.1016/j.egyr.2026.109113

  • 10

    AlqurashiA.KumarL.SinhaP. (2016). Urban land cover change modelling using time-series satellite images: a case study of urban growth in five cities of Saudi Arabia. Remote Sens.8 (10), 838. 10.3390/rs8100838

  • 11

    AmanM. M.JasmonG. B.BakarA. H. A.MokhlisH. (2013). A new approach for optimum DG placement and sizing based on voltage stability maximization and minimization of power losses. Energy Convers. Manag.70, 202–210. 10.1016/j.enconman.2013.02.015

  • 12

    AsadiM.PourhosseinK.NoorollahiY.MarzbandM.IglesiasG. (2023). A new decision framework for hybrid solar and wind power plant site selection using linear regression modeling based on GIS-AHP. Sustainability15 (10), 8359. 10.3390/su15108359

  • 13

    AydinN. Y.KentelE.Sebnem DuzgunH. (2013). GIS-Based site selection methodology for hybrid renewable energy systems: a case study from Western Turkey. Energy Convers. Manag.70, 90–106. 10.1016/j.enconman.2013.02.004

  • 14

    BarzehkarM.ParnellK. E.Mobarghaee DinanN.BrodieG. (2021). Decision support tools for wind and solar farm site selection in Isfahan province, Iran. Clean Technol. Environ. Policy23 (4), 1179–1195. 10.1007/s10098-020-01978-w

  • 15

    BeckH. E.McVicarT. R.VergopolanN.BergA.LutskoN. J.DufourA.et al (2023). High-resolution (1 km) köppen-geiger maps for 1901–2099 based on constrained CMIP6 projections. Sci. Data10 (1), 724. 10.1038/s41597-023-02549-6

  • 16

    CharabiY.GastliA. (2011). PV site suitability analysis using GIS-Based spatial fuzzy multi-criteria evaluation. Renew. Energy36 (9), 2554–2561. 10.1016/j.renene.2010.10.037

  • 17

    DavisN. N.BadgerJ.HahmannA. N.HansenB. O.MortensenN. G.KellyM.et al (2023). The global wind atlas: a high-resolution dataset of climatologies and associated web-based application. Bull. Am. Meteorological Soc.104 (8), E1507–E1525. 10.1175/BAMS-D-21-0075.1

  • 18

    ElboshyB.AlwetaishiM.AlyR. M. H.ZalhafA. S. (2022). A suitability mapping for the PV solar farms in Egypt based on GIS-AHP to optimize multi-criteria feasibility. Ain Shams Eng. J.13 (3), 101618. 10.1016/j.asej.2021.10.013

  • 19

    EzzM. S.HebaK.SalamaS. W. (2022). Determination of the optimal location for constructing solar photovoltaic farms (case study: obour city–egypt). Int. J. Adv. Res. Eng. Technol. (IJARET)13 (12), 42–56. 10.17605/OSF.IO/ZWBQ8

  • 20

    FarrT. G.RosenP. A.CaroE.CrippenR.DurenR.HensleyS.et al (2007). The shuttle radar topography mission. Rev. Geophys.45 (2), RG2004. 10.1029/2005RG000183

  • 21

    G. A. for S. and G. I. (GEOSA) (2021). “National geospatial platform,” in General Authority for Survey and Geospatial Information. Available online at: https://geoportal.sa (Accessed July 07, 2026).

  • 22

    GasparatosA.DollC. N. H.EstebanM.AhmedA.OlangT. A. (2017). Renewable energy and biodiversity: implications for transitioning to a green economy. Renew. Sustain. Energy Rev.70, 161–184. 10.1016/j.rser.2016.08.030

  • 23

    GuoJ.FastV.TeriP.CalvertK. (2020). Integrating land-use and renewable energy planning decisions: a technical mapping guide for local government. ISPRS Int. J. Geo-Information9 (5), 324. 10.3390/ijgi9050324

  • 24

    HassaanM. A. (2015). A GIS-Based suitability analysis for siting a solid waste-to-energy incineration plant in Alexandria, Egypt. Geogr. Inf. Syst.7, 269–279.

  • 25

    HassaanM. A.HassanA.Al-DashtiH. (2021). GIS-Based suitability analysis for siting solar power plants in Kuwait. Egypt. J. Remote Sens. Space Sci.24 (3), 453–461. 10.1016/j.ejrs.2020.11.004

  • 26

    HersbachH.BellB.BerrisfordP.HiraharaS.HorányiA.Muñoz‐SabaterJ.et al (2020). The ERA5 global reanalysis. Q. J. R. Meteorological Soc.146 (730), 1999–2049. 10.1002/qj.3803

  • 27

    IslamM. T.AliA. (2024). Sustainable green energy transition in Saudi Arabia: characterizing policy framework, interrelations and future research directions. Next Energy5, 100161. 10.1016/j.nxener.2024.100161

  • 28

    JuraszJ.CanalesF. A.KiesA.GuezgouzM.BelucoA. (2020). A review on the complementarity of renewable energy sources: concept, metrics, application and future research directions. Sol. Energy195, 703–724. 10.1016/j.solener.2019.11.087

  • 29

    KamatiK.SmitJ.HullS. (2022). Multicriteria decision method for siting wind and solar power plants in central north Namibia. Geomatics3 (1), 47–67. 10.3390/geomatics3010002

  • 30

    MalczewskiJ. (2006). GIS-Based multicriteria decision analysis: a survey of the literature. Int. J. Geogr. Inf. Sci.20 (7), 703–726. 10.1080/13658810600661508

  • 31

    MarquesA. T.BatalhaH.RodriguesS.CostaH.PereiraM. J. R.FonsecaC.et al (2014). Understanding bird collisions at wind farms: an updated review on the causes and possible mitigation strategies. Biol. Conserv.179, 40–52. 10.1016/j.biocon.2014.08.017

  • 32

    MbufuaN. A.Tiam KapenP.NgapgueF.Nzeukou TakougangA. (2025). Geospatial parametric approach for identifying optimal sites for wind-solar hybrid energy systems. Results Eng.27, 106448. 10.1016/j.rineng.2025.106448

  • 33

    Qassim University (2026). No Title Discover Qassim. Buraidah, Saudi Arabia: Qassim University. Available online at: https://www.qu.edu.sa/en/expolre-qassim (Accessed July 02, 2026).

  • 34

    RanaM. M. S. P.MoniruzzamanM. (2023a). A combined GIS, remote sensing and MCDM approach to find potential location for rainwater harvesting structure in northwestern part of Bangladesh. HydroResearch6, 235–246. 10.1016/j.hydres.2023.08.001

  • 35

    RanaM. M. S. P.MoniruzzamanM. (2023b). Potential application of GIS and remote sensing to evaluate suitable site for livestock production in northwestern part of Bangladesh. Watershed Ecol. Environ.5, 161–172. 10.1016/j.wsee.2023.07.001

  • 36

    RanaM. M. S. P.MoniruzzamanM. (2024). Demarcation of suitable site for solar photovoltaic power plant installation in Bangladesh using geospatial techniques. Next Energy3, 100109. 10.1016/j.nxener.2024.100109

  • 37

    RanaM. M. S. P.HossainM. A.NasherN. M. R. (2022). Identification of groundwater potential zone using geospatial techniques of agriculture dominated area in Dinajpur district, Bangladesh. Environ. Challenges7, 100475. 10.1016/j.envc.2022.100475

  • 38

    RanaM. M. S. P.RahmanM. T.HassanM. F. (2025). Mapping groundwater potential zone by robust machine learning algorithms and remote sensing techniques in agriculture dominated area, Bangladesh. Clean. Water3, 100064. 10.1016/j.clwat.2025.100064

  • 39

    SaatyT. L. (1977). A scaling method for priorities in hierarchical structures. J. Math. Psychol.15 (3), 234–281. 10.1016/0022-2496(77)90033-5

  • 40

    SaatyT. L. (1987). The analytic hierarchy Process—What it is and how it is used. Math. Model.9 (3–5), 161–176. 10.1016/0270-0255(87)90473-8

  • 41

    SaatyT. L. (2008). Decision making with the analytic hierarchy process. Int. J. Serv. Sci.1 (1), 83. 10.1504/IJSSCI.2008.017590

  • 42

    TaziG.JbaihiO.GhenniouiA.MerrouniA. A.BakkaliM. (2018). Estimating the renewable energy potential in Morocco: solar energy as a case study. IOP Conf. Ser. Earth Environ. Sci.161, 012015. 10.1088/1755-1315/161/1/012015

  • 43

    VillacresesG.GaonaG.Martínez-GómezJ.JijónD. J. (2017). Wind farms suitability location using geographical information system (GIS), based on multi-criteria decision making (MCDM) methods: the case of Continental Ecuador. Renew. Energy109, 275–286. 10.1016/j.renene.2017.03.041

  • 44

    World Bank Group, ESMAP, Solargis (2019). Global Solar Atlas 2.0: Technical Report. Washington, DC: The World Bank. Available online at: https://globalsolaratlas.info/(Accessed July 07, 2026).

Summary

Keywords

arid regions, GIS–AHP, hybrid renewable energy systems, onshore wind energy, solar PV suitability, solar–wind spatial complementarity, spatial interaction analysis, urban expansion planning

Citation

Ezz MS, Soliman AM, Salem DAH, Youssef HAH, Aldelgawy M and Khalil R (2026) A spatial GIS–AHP framework for integrating hybrid renewable energy suitability with urban growth planning in arid regions. Front. Built Environ. 12:1959364. doi: 10.3389/fbuil.2026.1959364

Received

05 August 2026

Revised

28 August 2026

Accepted

11 September 2026

Published

13 October 2026

Volume

12 - 2026

Edited by

Osama Omar, University of Bahrain, Bahrain

Reviewed by

M. Edwin, Anna University, India

M M Shah Porun Rana, University of Nebraska-Lincoln, United States

Updates

Copyright

*Correspondence: Mohamed Salah Ezz,

Disclaimer

All claims expressed in this article are solely those of the authors and do not necessarily represent those of their affiliated organizations, or those of the publisher, the editors and the reviewers. Any product that may be evaluated in this article or claim that may be made by its manufacturer is not guaranteed or endorsed by the publisher.

Outline

Figures

Cite article

Copy to clipboard


Export citation file


Share article

Article metrics