Abstract
The right-lateral Hasan Timur Lake Fault (HTLF), located approximately 40 km east of Lake Van, remains geomorphologically under characterized despite its influence on regional drainage and landscape evolution. The study area represents an active morphotectonic setting developed under strike-slip fault control, characterized by segment-scale morphological differentiation and a drainage network organized parallel to the fault trace. This study evaluates along-strike variability in surface responses using a multi-index morphometric framework. A 30 m digital elevation model (DEM) was analyzed through a GIS-based workflow implemented in ArcGIS Pro and integrated with MATLAB/TecDEM to derive key geomorphic indices, including the stream length–gradient index (SL), mountain-front sinuosity (Smf), valley floor width-to-height ratio (Vf), hypsometric integral and curves (HI–HE), and basin asymmetry factor (AF), for 78 fault-influenced micro-basins. The morphometric results reveal systematic spatial variations in basin geometry and drainage organization along the fault. S-shaped hypsometric curves characterize an intermediate stage of landscape development, reflecting the coupled effects of tectonic perturbation and fluvial erosion. In contrast, the concentration of convex hypsometric curves adjacent to the fault trace particularly in the southeastern sector indicates enhanced incision and geomorphic rejuvenation. Basin asymmetry patterns show a prevailing downstream leftward tilting in the northwestern and southeastern sectors, with localized rightward deviations in the central sector, suggesting spatially variable deformation reflected in basin-scale surface morphology. SL values in the southeastern sector, together with low Smf values and predominantly low Vf ratios, indicate steeper gradients, narrow valley floors, and straighter mountain fronts, collectively pointing to stronger geomorphic disequilibrium in this sector. These observations identify the southeastern segment of the HTLF as the most dynamically evolving part of the landscape.
1 Introduction
Earthquakes rank among the most destructive natural hazards, posing direct threats to human life and property. Throughout the 21st century, numerous great earthquakes (Mw ≥ 8) have occurred worldwide, resulting in substantial loss of life and severe economic damage (Han et al., 2025). This reality underscores the need particularly in regions located at the intersection of active plate boundaries and continental deformation belts to better constrain ongoing tectonic processes and fault behavior through multidisciplinary approaches. Türkiye is situated within the Alpine plate boundary belt and is strongly influenced by the continental collision between the Arabian and Eurasian plates. This geodynamic framework generates widespread and kinematically complex crustal deformation across the region. Such deformation is accommodated by active fault networks with diverse kinematics, dominated by strike-slip fault zones and thrust systems; consequently, Türkiye is characterized by high seismicity and pronounced neotectonics relief development (Şengör and Yazıcı, 2020; Zabcı and Şengör, 2025). Eastern Anatolia, in particular, represents a complex deformation domain in which collision-driven shortening is coupled with both right- and left-lateral strike-slip faulting (Şengör and Yazıcı, 2020). Therefore, quantifying the relative tectonic activity of individual fault segments is critical for understanding landscape evolution as well as for improving seismic hazard assessments. In tectonically active regions, crustal deformation exerts a primary control on topography through uplift, tilting, and faulting processes (Keller and Pinter, 2002; Khalifa et al., 2018; Mutlu, 2025a). Ongoing motions along fault zones associated with continental deformation generate characteristic tectonic landforms across a wide range of spatial scales (Giamboni et al., 2005; Gordon, 1998). The geomorphic response to such forcing is most clearly expressed in drainage networks, valleys, and basin geometry (Khalifa et al., 2018; Mutlu, 2025a). Accordingly, GIS-supported morphometric analyses are widely employed to detect and quantify active-tectonic signals preserved in the landscape (Keller and Pinter, 2002; Guo et al., 2023; El Hamdouni et al., 2008). Along active faults, geomorphic indices provide indirect yet robust proxies for deformation (Khalifa et al., 2018), enabling fault zones to be evaluated according to spatial variations in their morphological expression (Bull and McFadden, 1977; Rockwell et al., 1985). The successful application of these indices in diverse tectonic settings further highlights their value for comparative analyses (Mutlu, 2025a; Mutlu, 2025b; Wells et al., 1988). However, because individual indices may be influenced by lithology, climate, or local drainage conditions, a multi-index strategy is recommended to strengthen interpretations and reduce ambiguity (El Hamdouni et al., 2008; Dehbozorgi et al., 2010; Zygouri et al., 2015).
This study focuses on the Hasan Timur Lake Fault (HTLF), an active right-lateral strike-slip fault located approximately 40 km east of Lake Van in eastern Türkiye. The HTLF forms part of a regionally active deformation zone associated with major strike-slip fault systems (Emre et al., 2012; 2018). Based on its geometric characteristics, the HTLF has been interpreted as a connected structure and/or along-strike continuation of the Çaldıran Fault, which produced the 24 November 1976 Mw 7.0 earthquake (Toksöz et al., 1977). Despite instrumental seismicity in the region, direct evidence for a large historical earthquake occurring on the HTLF itself remains limited, and its tectonic activity has received relatively little attention in previous studies (Emre et al., 2012; Şaroğlu et al., 1987; Aktimur et al., 1979). The primary objective of this study is to quantitatively assess the relative tectonic activity of the HTLF and to identify spatial variations in deformation along the fault using a multi-index geomorphometric approach. Five key geomorphic indices are applied to fault-controlled drainage basins and valley systems: the stream length–gradient index (SL), mountain-front sinuosity (Smf), valley-floor width-to-height ratio (Vf), hypsometric integral and hypsometric curves (HI and HE), and basin asymmetry factor (AF). By jointly interpreting channel, valley, and basin-scale indicators, this study aims to characterize the geomorphic expression of active deformation and to identify fault segments exhibiting relatively higher tectonic influence. The results provide new insights into the surface response to tectonic forcing along the HTLF and contribute to a refined understanding of neotectonics processes in Eastern Anatolia, with implications for future studies in active tectonics, geomorphology, and seismic hazard assessment.
2 Regional tectonic and geological setting
Eastern Anatolia is one of the key regions where contractional tectonics associated with the continental collision between the Arabian and Eurasian plates can be most clearly observed (Şengör and Yazıcı, 2020). Following the complete consumption of the last remnants of oceanic lithosphere during the Late Miocene, continental collision initiated at approximately 13 Ma along the Bitlis–Zagros Suture Zone, establishing the fundamental framework that governs the present-day geodynamic architecture of the region (Şengör and Kidd, 1979; Dewey et al., 1986; Şaroğlu and Yılmaz, 1986; Okay et al., 2010). This collision resulted in intense crustal shortening and thickening accompanied by substantial surface uplift, controlling the development of the East Anatolian High Plateau. The plateau has risen by approximately 2 km since the Middle Miocene and continues to undergo uplift today (Yılmaz et al., 1987; Şengör et al., 2008). Accordingly, the contractional tectonic regime generated by continental collision is considered the primary driving mechanism of regional deformation in Eastern Anatolia (Şengör and Yazıcı, 2020). In the Van region, ongoing deformation is governed by a complex tectonic framework characterized by pronounced strike-slip components, involving both right- and left-lateral motions, together with active thrust faulting (Özkaymak et al., 2011; Koçyiğit, 2013; Selçuk, 2016). Within this framework, the principal active fault systems mapped in and around the Van Lake Basin (Figure 1) include the Çaldıran Fault, the Van Fault Zone, the Saray Fault Zone, the Dorutay Fault, the Erciş Fault, the Southeast Anatolian Thrust Belt, the Başkale Fault, and several strike-slip systems that extend eastward into Iran (Emre et al., 2018; Özkaymak et al., 2011; Koçyiğit, 2013). Numerous destructive and moderate-to-large earthquakes have occurred in the Van region during both historical and instrumental periods (Figure 1), confirming that it constitutes one of the highest seismic hazard zones in Eastern Anatolia (Ambraseys, 2009; AFAD, 2025).
FIGURE 1
Considering the seismicity of Van Province and its surroundings (Figure 1), the 23 October 2011 Mw 7.1 Tabanlı (Van) earthquake represents a critical event for understanding the seismotectonic evolution of the Van Basin (Özkaymak et al., 2011; Koçyiğit, 2013). Prior to this earthquake, the fault plane responsible for the mainshock had neither been described in detail in the scientific literature nor clearly depicted on existing active fault maps. Post-earthquake geological and geophysical investigations demonstrated that surface rupture occurred along the Van Fault Zone, thereby clarifying one of the principal structural elements controlling active deformation within the basin (Emre et al., 2018; Koçyiğit, 2013; Selçuk, 2016). Another major destructive earthquake affecting the broader vicinity of the study area occurred along the Çaldıran Fault (Figure 1). The Çaldıran Fault, one of the major active fault systems in Eastern Anatolia, together with the eastward-extending North Tabriz Fault (NTF), forms part of a major strike-slip fault zone that defines the southern boundary of the Lesser Caucasus. The Çaldıran Fault has generated numerous destructive earthquakes during both historical and instrumental periods; among these, the 24 November 1976 Mw 7.0 earthquake stands out as one of the most significant regional events, resulting in 3480 fatalities and widespread building collapse and severe structural damage (Toksöz et al., 1977; AFAD, 2025; Eyidoğan et al., 1991; Selçuk et al., 2016; Mutlu and Günday, 2024). Collectively, these major earthquakes demonstrate that the Van Basin and its surroundings constitute a region of exceptionally high seismic hazard directly linked to active fault systems (Figure 1). In this context, numerous morphometric index-based studies have been conducted within the region and in the vicinity of the HTLF to evaluate the geomorphic expressions of active tectonics (Sağlam Selçuk and Düzgün, 2017; Sağlam Selçuk and Kul, 2021; Zorer and Avcı, 2022; Avci and Sunkar, 2023; Matpay, 2024; Mutlu, 2025a; Mutlu, 2025b). However, to date, no comprehensive morphometric index analysis has been carried out specifically focusing on the Hasan Timur Lake Fault (HTLF) itself. Within this regional fault network, the Hasan Timur Lake Fault (HTLF), located east of Lake Van near the international border, can be regarded as an active strike-slip structure that may play a critical linkage or transfer role in accommodating and transmitting deformation between adjacent fault segments.
The HTLF is clearly expressed in the landscape. As shown in Figure 2a, the lineament highlighted by blue arrows on the shaded-relief map delineates the main deformation belt of the HTLF as it is manifested at the surface. This linear feature is characterized by systematic geomorphic expressions, including abrupt deflections in stream and valley orientations, aligned ridge crests, and sharp morphological breaks on hillslope surfaces. The persistence and coherence of these geomorphic discontinuities across kilometer-scale distances indicate that the HTLF represents an active fault zone with regional continuity rather than a localized structural lineament. In its regional topographic context, the HTLF extends in a NE–SW direction along the Yukarıbalçıklı–Oymaklı–Eğribelen–Aşağıtulgalı corridor toward the vicinity of the Iran border (Figure 2b). Along this trend, the fault forms a distinct morphotectonic boundary separating higher-relief mountainous terrain to the east from lower-gradient surfaces to the west, further emphasizing its role in controlling regional landscape organization.
FIGURE 2
Examination of the geological map of the study area (Akbaş et al., 2011) (Figure 3) shows that the NW–SE–trending HTLF clearly defines a geotectonic boundary between Quaternary basin-fill deposits and Upper Cretaceous–Paleocene ophiolitic/complex basement units. The sharp juxtaposition of lithologic contacts along the fault trace, the linear truncation of stratigraphic units, and the concentration of young deposits within the fault zone indicate that the HTLF represents an active deformation corridor rather than a purely morphologic lineament, exerting strong structural control on both lithology and topography. The map highlights the widespread distribution of young units north of the HLGF, including Quaternary alluvium (Q) and Pliocene-Pleistocene basalts (plQb), as well as Pliocene clastic deposits (plç) predominantly exposed in the southern sector. The along-strike, fault-parallel arrangement of these units, together with their locally elongated, strip-like geometries adjacent to the fault, suggests that the HTLF has played a fundamental role in controlling Neogene-Quaternary depositional domains, particularly basin and plain-floor development. Notably, sectors where alluvial deposits widen are interpreted as being consistent with releasing segments commonly associated with strike-slip fault systems, or with localized subsidence related to minor along-strike variations in fault geometry (Figure 3).
FIGURE 3
3 Materials and methods
Four datasets were used: (i) active faults, (ii) instrumental seismicity, (iii) a digital elevation model (DEM), and (iv) geological maps. Active faults were obtained from the 1:250,000 Scale Active Fault Map Series of Turkey, Başkale (NJ 38-6) quadrangle (Emre et al., 2012). Earthquake data were compiled from AFAD (2025). Topographic analyses were based on SRTM DEM data. A 30 × 30 m spatial resolution Digital Elevation Model (DEM) was used for the topographic analyses. Higher resolutions may introduce excessive sensitivity due to micro-topographic roughness, whereas lower resolutions may fail to capture segment-scale morphological variations. Therefore, the 30 m DEM provides an optimal balance and sufficient topographic detail for reliable basin-scale morphometric analysis. Geological information was derived from Aktimur et al. (1979), Ateş et al. (2007), and Akbaş et al. (2011). DEM-based morphometric analyses were performed using TecDEM in the MATLAB environment (Shahzad and Gloaguen, 2011a; Shahzad and Gloaguen, 2011b). Drainage-network extraction and longitudinal-profile analyses followed Strahler stream ordering (Strahler, 1957) applied to filled DEMs (Planchon and Darboux, 2002). The critical contributing-area threshold was determined using a trial-and-error procedure (Shahzad and Gloaguen, 2011a; Shahzad and Gloaguen, 2011b), and threshold values of 1 and 2 were applied for basin delineation.
TecDEM was used to derive the drainage network, sub-basins, and the stream length–gradient index (SL) (Shahzad and Gloaguen, 2011a; b). These outputs were further processed in ArcGIS Pro and finalized cartographically in Adobe Illustrator. Mountain-front sinuosity (Smf), basin asymmetry factor (AF), and valley-floor width-to-height ratio (Vf) were calculated in ArcGIS Pro. Hypsometric integrals (HI) and hypsometric curves (HC) were generated using the CalHypso GIS tool (Pérez-Peña et al., 2009a; Pérez-Peña et al., 2009b; Pérez-Peña et al., 2010). Using these datasets and procedures, the drainage area structurally controlled by the HTLF was subdivided into 78 micro-basins for detailed morphometric analysis, and the selected indices were calculated separately for each unit (Figure 4).
FIGURE 4
3.1 Hypsometric curve (HC) and hypsometric integral (HI)
The Hypsometric Integral (HI) is widely used to assess landscape evolution and relative tectonic activity (Strahler, 1952; Keller and Pinter, 2002). It is calculated from the mean elevation of a basin relative to its minimum and maximum elevations (Equation 1) and ranges between 0 and 1 (Pike and Wilson, 1971; Keller and Pinter, 2002). Higher HI values generally indicate less eroded or rejuvenated topography, whereas lower values reflect more advanced stages of denudation (Strahler, 1952; Willgoose, 1994; Keller and Pinter, 2002). The HI corresponds to the area under the hypsometric curve, whose interpretation follows the approach of Strahler (1952) and Keller and Pinter (2002). DEM-based GIS implementations allow basin-scale and segment-scale comparisons of relative tectonic activity along active faults (Silva Barroso et al., 2003; El Hamdouni et al., 2008; Mutlu, 2025a; Mutlu, 2025b). In Equation 1, H represents mean basin elevation, Hmin the minimum elevation, and Hmax the maximum elevation (Pérez-Peña et al., 2010; Giaconia et al., 2012).
3.2 Basin asymmetry factor (AF)
The basin asymmetry factor (AF) is widely applied to evaluate planform basin asymmetry and possible tectonic tilting (Hare and Gardner, 1985; Keller and Pinter, 2002). AF compares the area on the right side of the trunk stream (Ar), defined relative to the downstream direction, with the total basin area (At) (Equation 2). AF has been extensively used to detect tilt anomalies associated with active faulting and to distinguish tectonic influences from other external controls (Pérez-Peña et al., 2010; Giaconia et al., 2012). In this study, asymmetry magnitude independent of tilt direction was assessed using the absolute deviation from 50 (AF_dev = |AF − 50|). Basin classes follow Pérez-Peña et al. (2010) and Giaconia et al. (2012): <5 (low or symmetric), 5–10 (moderate), 10–15 (asymmetric), and >15 (highly asymmetric).
The basin asymmetry factor (AF) is defined as the ratio of the basin area on the right side of the trunk stream (Ar) to the total basin area (At), measured relative to the downstream flow direction. A perfectly symmetric basin theoretically yields an AF value close to 50. Deviations from this value indicate the side on which asymmetry is concentrated and the direction of lateral channel migration. AF values greater than 50 indicate a relatively larger right-side area. This condition generally implies leftward migration of the trunk stream. In contrast, AF values lower than 50 indicate a wider left-side basin area. This pattern suggests rightward migration of the main channel. Such directional deviations from symmetry may reflect tectonic tilting at the basin scale. Therefore, the sign of deviation from AF = 50 is commonly used to infer channel migration and tilt direction in tectonically active regions (Hare and Gardner, 1985; Keller and Pinter, 2002; Pérez-Peña et al., 2010; Giaconia et al., 2012).
3.3 Stream length–gradient index (SL)
The stream length–gradient (SL) index is widely used in longitudinal river-profile analysis to identify abrupt variations in channel slope (Hack, 1973). It quantifies local gradient changes and associated topographic irregularities along a stream course. SL is closely related to stream power because it reflects the hydraulic energy available within a channel reach and its potential for sediment transport and incision (Hack, 1973). Owing to its sensitivity to slope variations, SL is effective in detecting knickpoints and related anomalies (Burbank and Anderson, 2001). SL values may be influenced by lithology, tectonic deformation, base-level changes, and spatial variations in stream power (Hack, 1973; Burbank and Anderson, 2001). In areas lacking strong lithologic contrasts, significant SL anomalies are commonly interpreted as indicators of tectonic forcing. For this reason, SL is frequently applied in studies of relative tectonic activity (Merritts and Vincent, 1989; Keller and Pinter, 2002; Chen et al., 2003). Because SL is also affected by rock strength, lithologic control must be considered when interpreting anomalies (Burbank and Anderson, 2001; Keller and Pinter, 2002). Previous studies have shown a positive correlation between SL and uplift rates, with higher values typically observed in actively deforming regions (Keller and Pinter, 2002; El Hamdouni et al., 2008). In this study, SL was calculated using Equation 3 (Hack, 1973; Keller and Pinter, 2002).
The variables used in this study are defined as follows. SL represents the stream length–gradient index. ΔH denotes the elevation difference between the maximum and minimum channel-bed elevations within the selected stream reach. ΔL corresponds to the channel-length interval of the same reach. The ratio ΔH/ΔL therefore defines the longitudinal gradient, or channel slope. L is the distance, measured in meters, from the midpoint of the analyzed stream segment to the most distant headwater point. This point corresponds to the upstream end of the channel.
3.4 Mountain-front sinuosity (Smf)
Mountain-front sinuosity (Smf) Equation 4 is widely used to quantify the linearity of fault-controlled mountain fronts (Bull and McFadden, 1977; Keller and Pinter, 2002; Bull, 2007). It is commonly applied to assess relative morphotectonic activity. Smf values close to 1 indicate a nearly straight mountain front. This geometry is typically associated with active uplift and strong tectonic control. Higher Smf values reflect increasingly sinuous mountain fronts. Such geometries generally indicate reduced tectonic influence and a greater role of erosional processes (Rockwell et al., 1985; Silva Barroso et al., 2003; Bull, 2007; Pérez-Peña et al., 2010; Keller and Pinter, 2002).
In this study, Lmf represents the sinuously traced (true planimetric) length of the mountain-front line as mapped on the ground, whereas Ls denotes the straight-line distance between the two end points of the same mountain-front segment.
3.5 Valley floor width-to-height ratio (Vf)
The valley floor width-to-height ratio (Vf) Equation 5 is widely used to quantify valley geometry in relation to tectonic forcing (Bull and McFadden, 1977; Bull, 2007). It is commonly applied in studies of fault activity and uplift. Vf is defined as the ratio of valley-floor width to total valley height. Valley height corresponds to the vertical distance between the valley floor and the highest point on the adjacent valley sides (Bull and McFadden, 1977; Bull, 2007). Low Vf values indicate narrow and deeply incised valleys. These forms are generally associated with active tectonic conditions. High Vf values correspond to wider and shallower valleys, where lateral erosion is more dominant and tectonic influence is reduced (Keller and Pinter, 2002; Rockwell et al., 1985; Silva Barroso et al., 2003; El Hamdouni et al., 2008).
The Vf index is calculated using the following formula: Vfw: Valley floor width (m). Eld: Peak elevation of the left valley wall (m). Erd: Peak elevation of the right valley wall (m). Esc: Valley floor elevation (m).
4 Results
4.1 Hypsometric curve (HC) and hypsometric integral (HI)
Hypsometric integrals (HI) and hypsometric curves (HC) were calculated for 78 sub-basins controlled by the Hasan Timur Lake Fault (HTLF) (Figure 5). Based on HI values, 12 sub-basins are classified as youthful (HI > 0.5), 49 as mature or equilibrium-stage basins (0.3 < HI < 0.5), and 17 as old-stage basins (HI < 0.3). Convex and S-shaped hypsometric curves cluster spatially near the mapped fault trace (Figure 5). The convex-class basins include Basins 27, 30, 28, 29, 15, 43, 20, 22, 3, 21, 26, and 36 (Figure 6a). Their convex morphology corresponds to a youthful landscape state developed under relatively strong tectonic forcing. The southeastern sector of the HTLF exhibits a clear differentiation of hypsometric classes (Figure 5). Micro-basins 26–29 fall within the convex category and display high HI values. These basins are developed on Upper Cretaceous mélange (unit om; Figure 3). The recurrence of high HI values within multiple basins formed on the same lithologic unit indicates that the observed distribution cannot be explained solely by lithology. The concentration of convex basins in this sector is consistent with a stronger tectonic influence along the southeastern segment of the HTLF. S-shaped hypsometric curves dominate a large part of the study area (Figure 5; Figures 6b–e). These basins represent an intermediate morphodynamic stage. Uplift and erosional processes operate simultaneously, and the landscape is partially adjusting toward equilibrium conditions. Concave basins occur mainly at greater distances from the fault or in sectors where topography has been more extensively reworked (Figure 5; Figure 6f). This geometry reflects a more advanced erosional stage and a comparatively weaker uplift signal.
FIGURE 5
FIGURE 6
4.2 Basin asymmetry factor (AF)
The Asymmetry Factor (AF) was calculated for the micro-basins controlled by the Hasan Timur Lake Fault (HTLF) (Figure 7). Among the 78 analyzed sub-basins, 36 are classified as dominantly and moderately asymmetric, whereas 42 fall into the low-asymmetric and symmetric classes (Figure 7). Dominantly and moderately asymmetric basins are concentrated in the northwestern (NW) and southeastern (SE) segments of the HTLF. In contrast, low-asymmetric and symmetric basins are heterogeneously distributed along the fault-controlled drainage system. The clustering of dominantly and moderately asymmetric classes near the HTLF indicates that the fault zone is sufficiently active to influence basin geometry and trunk-stream position (Figure 7a). Increased asymmetry in micro-basins elongated parallel to the fault trace is consistent with segment-controlled deformation domains typical of strike-slip fault systems. Conversely, the broader distribution of symmetric and weakly asymmetric basins in areas relatively distant from the fault suggests either a weaker tilting component or a more balanced drainage configuration shaped by fluvial processes.
FIGURE 7
In the southeastern sector of the HTLF, marked variability in AF classes is observed in micro-basins located close to the fault trace, particularly around basins 26–32 (Figure 7a). The presence of dominantly and moderately asymmetric basins in this sector reflects enhanced deformation near the fault termination. However, the coexistence of symmetric basins within the same area indicates that the asymmetry signal is heterogeneously distributed between segments and even among adjacent basins. This pattern demonstrates that tectonic control operates together with lithology and drainage organization. The AF direction map along the HTLF shows that 37 sub-basins are oriented rightward relative to the downstream flow direction, whereas 41 sub-basins are oriented leftward (Figure 7b). Among the rightward-oriented basins, six exhibit dominant asymmetry (Basins 6, 21, 30, 32, 45, and 60). Among the leftward-oriented basins, thirteen display dominant asymmetry (Basins 1, 2, 15, 17, 26, 39, 51, 54, 56, 63, 68, 69, and 70). These basins are located directly along the fault zone. The clear spatial organization of AF directions indicates that basin asymmetry is not random but largely controlled by the fault zone. In the NW and SE segments, AF arrows predominantly show a downstream leftward tendency (Figure 7b). This pattern indicates that drainage planforms have been reorganized consistently within a common deformation field in these segments. In strike-slip fault zones, stress transfer near segment terminations and local variations in fault strike commonly generate directional channel migration. Therefore, the leftward tendency observed in the NW and SE segments is interpreted as a morphometric indicator of stronger tectonic control in these parts of the HTLF (Figure 7b). By contrast, the central segment, characterized by comparatively lower relief and a more equilibrated topography, exhibits predominantly rightward AF orientations (Figure 7b). Overall, the spatial contrast—leftward tendencies in the NW and SE segments versus rightward tendencies in the central segment—demonstrates that deformation along the HTLF is not uniform. Basin-scale channel migration and asymmetry direction vary in a segment-controlled manner (Figure 7b). Accordingly, the AF direction map provides strong morphometric evidence that the drainage network has been reorganized differently along distinct fault segments. It also shows that the geomorphic expression of tectonic forcing varies spatially along the fault zone. When evaluated together with the geological map, the AF direction pattern indicates that drainage asymmetry along the HTLF is controlled by the combined effects of segment-controlled tectonic forcing and lithological resistance contrasts (Figures 3, 7b). The downstream rightward tendency in the central segment is associated with relatively weaker and heterogeneous units, including Pliocene–Pleistocene basalts (plQb), Pliocene clastics (plç), and locally Quaternary alluvium (Q), which allow easier lateral channel adjustment (Figures 3, 7b). In contrast, the dominant downstream leftward tendency in the NW segment occurs where resistant Upper Cretaceous–Paleocene volcaniclastic–sedimentary units (k2b) and Upper Cretaceous cherts (k2ç) prevail. In the SE segment, Upper Cretaceous mélange (om) coexists with younger units. These conditions favor clearer preservation of tectonically driven directional channel migration (Figure 7b).
4.3 Stream length–gradient index (SL)
SL values were calculated for streams controlled by the Hasan Timur Lake Fault (HTLF), ranging between 0.37 and 235. Because the stream length–gradient (SL) index is sensitive to channel slope and incision processes, lithologic resistance contrasts must be explicitly considered when interpreting SL anomalies. Accordingly, lithologic units in the study area were adapted to five relative rock-strength classes at the field scale, following the rock-mass strength approach of Selby (1980) (Figure 8). The very high-strength class includes chert, gabbro, peridotite, and basalt. The high-strength class comprises trachyte–andesite, massive or well-cemented limestone, and volcaniclastic–sedimentary assemblages dominated by volcanic components. The moderate-strength class includes metaclastics, variably cemented sandstone–mudstone–limestone sequences, and conglomerate–sandstone–mudstone alternations. The low-strength class consists of pyroclastic rocks and mélange. The very low-strength (unconsolidated) class includes alluvium, colluvial slope deposits, and alluvial fan units (Selby, 1980). SL values were mapped in five classes (0–15, 15–30, 30–80, 80–150, and 150–236). In the same map, lithologic resistance is represented by a grayscale gradient ranging from very low (white) to very high (black) (Figure 8). This combined representation facilitates spatial differentiation of SL patterns along longitudinal profiles and supports the discrimination of tectonic versus lithologic controls. Low SL values (green: 0–15; yellow: 15–30) are widespread in low-gradient intra-basin reaches, particularly where streams develop on low-to moderate-strength lithologies (Figure 8). These zones correspond to reduced channel slope, lower stream power, and limited bed incision. On weak substrates, channels may exceed erosion thresholds more easily and develop smoother longitudinal profiles without generating pronounced anomalies. Therefore, low SL values do not necessarily reflect weak tectonic forcing. Lithologic weakness may also reduce SL by smoothing the longitudinal profile. Intermediate SL values (orange: 30–80) occur both near and away from the fault. They are especially pronounced where stream segments coincide with lithologic boundaries and relief transitions (Figure 8). These reaches represent zones of increased channel gradient without producing sharp slope breaks. High SL values (red: 80–150; dark red: 150–236) are spatially restricted and occur as localized clusters. The highest SL values (approximately 200–230) in the southeastern segment of the HTLF were obtained both within resistant volcaniclastic–sedimentary units and within low-strength mélange (Figure 8). The occurrence of similarly high SL anomalies across contrasting rock-strength classes, and their lack of consistent correlation with lithologic variations, indicates a significant tectonic contribution. Accordingly, high SL clusters located near the fault zone represent sectors where tectonic control is more pronounced. These anomalies are interpreted to reflect localized uplift and/or enhanced incision associated with segment-scale deformation along the HTLF.
FIGURE 8
4.4 Mountain-front sinuosity (Smf)
Mountain-front sinuosity (Smf) was calculated for the mountain-front belts along the HTLF on a segment basis. For both Smf and Vf measurements, the Hasan Timur Lake Fault (HTLF) was subdivided into five segments (S1–S5) from northwest (NW) to southeast (SE), based on step-overs, bends, and variations in fault strike. The calculated Smf values range from 1.114 to 1.352 (Figure 9). These values indicate that the mountain front generally preserves a near-linear geometry and remains strongly controlled by tectonics. Segment-based results show that S1 yields the lowest Smf value (Smf = 1.114), representing the most linear mountain-front geometry. Segments S2 (Smf = 1.224), S3 (Smf = 1.183), and S5 (Smf = 1.197) also fall within a low-sinuosity range (∼1.18–1.22), indicating only minor curvature along the mountain-front trace (Figure 9). In contrast, S4 exhibits the highest Smf value (Smf = 1.352). This value reflects a comparatively more curvilinear mountain-front geometry in this segment (Figure 9). The increased sinuosity along S4 is associated with enhanced hillslope processes, lithologic resistance contrasts, and/or minor variations in segment strike that amplify the topographic expression. Overall, the relatively low Smf values along the HTLF (∼1.1–1.35) support a predominantly linear mountain front and pronounced tectonic control. However, the relative increase observed in S4 indicates that geomorphic responses are not uniform along strike and vary between fault segments (Figure 9).
FIGURE 9
4.5 Valley-floor width-to-height ratio (Vf)
In this study, the valley-floor width–to–height ratio (Vf) was calculated to quantitatively assess the morphologic response of fluvial valleys along the Hasan Timur Lake Fault (HTLF). Vf measurements were conducted at 36 cross-sections located on valleys subparallel and adjacent to the fault (Figure 10). The obtained Vf values range from 0.07 to 11.11 (Table 1). The dataset reveals clear segment-scale variations in valley geometry along the fault zone (Figure 10; Table 1). In the northwestern (NW) sector (S1 segment), Vf values are generally low to moderate, indicating the predominance of narrow valley floors. Values below 1 occur at Vf-1 (0.67) and Vf-5 (0.24). However, locally higher values are also observed (Vf-2 = 2.50; Vf-3 = 2.15; Vf-4 = 2.29). This distribution indicates that valley morphology at the NW tip is heterogeneous. Local controls such as lithology, tributary input, and segment geometry likely influence the Vf response. The central part of the fault, particularly the S2 segment, exhibits the highest concentration of Vf < 1 values. Numerous cross-sections yield low Vf values (Vf-6 = 0.89; Vf-8 = 0.12; Vf-9 = 0.94; Vf-10 = 0.16; Vf-11 = 0.27; Vf-12 = 0.96; Vf-13 = 0.92; Vf-14 = 0.64; Vf-15 = 0.89; Vf-16 = 0.40; Vf-20 = 0.29; Vf-21 = 0.29). These values reflect narrow and deeply incised valleys and enhanced vertical incision. Nevertheless, cross-sections with Vf ≈ 1 or higher (Vf-7 = 1.07; Vf-19 = 1.11; Vf-18 = 1.88) demonstrate that wider valley floors can locally develop within the same segment. This variability indicates that geomorphic response is not uniform even within a single structural domain. In the transitional S3 segment, the persistence of low Vf values decreases, whereas higher Vf values become more prominent (Vf-22 = 5.00; Vf-23 = 1.20; Vf-24 = 1.61). This pattern reflects a progressive widening of valley floors along this section. The southeastern (SE) sector, comprising segments S4 and S5, displays a bimodal Vf distribution. Very low and very high Vf values occur in close proximity to segment boundaries. In S4, Vf < 1 values (Vf-26 = 0.29; Vf-27 = 0.53; Vf-28 = 0.20) indicate narrow valley floors. In contrast, an extreme value (Vf-29 = 11.11) represents a markedly wide and relatively mature valley reach. In the S5 segment, most measurements fall within the Vf < 1 range (Vf-30 = 0.25; Vf-31 = 0.93; Vf-32 = 0.28; Vf-33 = 0.07; Vf-34 = 0.17; Vf-35 = 0.24; Vf-36 = 0.34). This clustering highlights the dominance of narrow valley floors. Notably, Vf-33 (0.07) is the lowest value obtained in this study and indicates pronounced incision at the SE tip. Overall, the concentration of Vf < 1 values in the S2 segment and their renewed dominance in the SE sector, particularly in S5, demonstrate that valley morphology varies systematically at the segment scale. Narrow and deeply incised valleys are concentrated within specific structural domains along the HTLF (Figure 10; Table 1).
FIGURE 10
TABLE 1
| Vf No | Vfw | Erd | Eld | Esc | Vf | Distance to the mountain front (m) |
|---|---|---|---|---|---|---|
| 33 | 6 | 2460 | 2442 | 2360 | 0.07 | 476 |
| 8 | 3 | 2205 | 2205 | 2180 | 0.12 | 560 |
| 10 | 6 | 2240 | 2225 | 2195 | 0.16 | 582 |
| 34 | 13 | 2490 | 2500 | 2420 | 0.17 | 716 |
| 28 | 12 | 2445 | 2455 | 2390 | 0.20 | 580 |
| 5 | 5 | 2142 | 2150 | 2125 | 0.24 | 213 |
| 35 | 14 | 2520 | 2495 | 2450 | 0.24 | 1227 |
| 30 | 18 | 2430 | 2432 | 2360 | 0.25 | 477 |
| 11 | 10 | 2315 | 2280 | 2260 | 0.27 | 959 |
| 32 | 25 | 2510 | 2550 | 2440 | 0.28 | 890 |
| 20 | 2 | 2095 | 2099 | 2090 | 0.29 | 37 |
| 21 | 4 | 2148 | 2160 | 2140 | 0.29 | 127 |
| 26 | 12 | 2243 | 2240 | 2200 | 0.29 | 20 |
| 36 | 16 | 2405 | 2390 | 2350 | 0.34 | 832 |
| 16 | 4 | 2140 | 2130 | 2125 | 0.40 | 357 |
| 27 | 80 | 2450 | 2550 | 2350 | 0.53 | 1100 |
| 14 | 8 | 2250 | 2235 | 2230 | 0.64 | 556 |
| 1 | 30 | 2310 | 2315 | 2268 | 0.67 | 240 |
| 6 | 20 | 2170 | 2135 | 2130 | 0.89 | 245 |
| 15 | 20 | 2225 | 2240 | 2210 | 0.89 | 335 |
| 13 | 30 | 2255 | 2230 | 2210 | 0.92 | 347 |
| 31 | 20 | 2450 | 2433 | 2420 | 0.93 | 900 |
| 9 | 15 | 2195 | 2183 | 2173 | 0.94 | 349 |
| 12 | 12 | 2235 | 2230 | 2220 | 0.96 | 179 |
| 7 | 40 | 2200 | 2185 | 2155 | 1.07 | 524 |
| 19 | 15 | 2116 | 2117 | 2103 | 1.11 | 1010 |
| 23 | 6 | 2185 | 2181 | 2178 | 1.20 | 630 |
| 24 | 25 | 2165 | 2170 | 2152 | 1.61 | 84 |
| 18 | 15 | 2109 | 2115 | 2104 | 1.88 | 170 |
| 25 | 40 | 2230 | 2210 | 2200 | 2.00 | 250 |
| 3 | 70 | 2190 | 2165 | 2145 | 2.15 | 720 |
| 4 | 40 | 2180 | 2155 | 2150 | 2.29 | 170 |
| 2 | 25 | 2200 | 2180 | 2180 | 2.50 | 500 |
| 17 | 90 | 2115 | 2095 | 2070 | 2.57 | 1080 |
| 22 | 100 | 2163 | 2163 | 2143 | 5.00 | 440 |
| 29 | 50 | 2415 | 2412 | 2409 | 11.11 | 370 |
Table of Vf values calculated along the HTLF.
5 Discussion
The HTLF is a right-lateral strike-slip fault located approximately 40 km east of Lake Van within the active strike-slip deformation belt of Eastern Anatolia. In this study, HI/HE, AF, SL, Smf, and Vf indices were jointly evaluated for 78 fault-controlled micro-basins along the HTLF. An integrated assessment of these indices was also performed (Figure 11). First, basin-scale Asymmetry Factor (AF) and Hypsometric Integral (HI) values were combined. The average of the two indices, expressed as (AF + HI)/2, was used to generate a composite tectonic classification. In addition, Vf, Smf, and SL values that indicate high tectonic influence were overlaid to provide a comprehensive representation (Figure 11). The resulting polygon-based classification shows that high tectonic class basins (red) cluster near the fault trace and at segment terminations. Moderate and low tectonic classes are more widely distributed and vary between segments. This spatial pattern indicates that deformation along the fault is not uniform but segment-controlled. Vf measurements plotted on the map show that narrow and deeply incised valleys (Vf < 0.5) largely coincide with the high tectonic class. This pattern indicates that vertical incision is concentrated in specific segments and supports the basin-scale morphometric signal. Moderate and high Vf values display a more localized distribution, reflecting along-strike variability in valley morphology. Smf values indicate that the mountain front generally preserves a linear geometry. However, slightly higher sinuosity occurs in certain segments. These variations reflect local topographic processes, lithologic contrasts, and subtle differences in segment geometry. High SL values spatially correspond to the high tectonic class. Abrupt changes in channel gradient cannot be explained solely by lithology and indicate tectonic control. The clustering of high SL anomalies in specific segments supports the presence of differential uplift and/or a tilting component along the fault. Overall, the combined evaluation of (AF + HI)/2 basin classification with Vf, Smf, and SL indices demonstrates that tectonic activity along the HTLF is spatially variable and segment-controlled. The multi-index approach provides a more robust interpretation than reliance on a single morphometric parameter. It highlights the integrated structural control of the fault on drainage organization and topography. To evaluate potential climatic influence on basin and drainage evolution, meteorological data were also examined. Long-term records from the Van Meteorological Station (1939–2025) indicate a mean annual temperature of 9.5 °C. The mean annual maximum and minimum temperatures are 15.1 °C and 3.8 °C, respectively. Precipitation is strongly seasonal, with a maximum in April (54.9 mm) and a minimum in August (5.7 mm). The mean annual precipitation is 393.3 mm (TSMS, 2026). Although this continental climate produces seasonal fluctuations in fluvial activity, it does not adequately explain the segment-scale morphometric patterns observed along the HTLF. First, climatic forcing is broadly similar across the study area, whereas the indices display systematic spatial variations aligned with fault segments. Second, high SL anomalies occur within contrasting lithologic strength classes in specific sectors. This indicates that channel gradient and incision are primarily controlled by tectonic forcing (uplift, tilting, channel migration) and lithologic resistance rather than by climate alone.
FIGURE 11
At the regional tectonic scale (Figure 12), the HTLF occupies an intermediate (transfer) position within the Lake Van–Lake Urmia strike-slip deformation corridor. The fault facilitates stress and displacement transfer between adjacent segments and fault zones. To the north, the Balık Lake Fault Zone (∼3.22 mm/yr) (Mutlu, 2022) and strike-slip structures around the Iğdır–Doğubeyazıt region accommodate part of the regional shear. To the northwest, the Çaldıran Fault (∼3.27 mm/yr) (Selçuk et al., 2016) represents one of the most prominent slip-rate structures in the region and provides kinematic continuity with the HTLF. West of the HTLF, basin-bounding faults of the Van Basin, together with the Erciş Fault (∼2.02 mm/yr) (Sağlam Selçuk and Kul, 2021) and structures such as the Van (Tabanlı) and Yeniköşk faults, define a domain where deformation is distributed at the basin scale. To the east and southeast, the Galitu–Siyahçeşme Fault Zone (∼2–4 mm/yr) (Copley and Jackson, 2006), the Mishu Fault (∼2.62 mm/yr) (Su et al., 2016), and farther east the North Tabriz Fault Zone (∼7.7 mm/yr) (Rizza et al., 2013) form a strike-slip system extending into Iran. This configuration indicates that the HTLF is not an isolated local structure but part of a transboundary deformation network. To the south, faulting along the Başkale–Salmas trend and structures associated with the Bitlis–Zagros Suture Zone reflect the concurrent influence of compressional tectonics within the broader system. Taken together, the spatial arrangement and regional slip-rate pattern indicate that the HTLF does not accommodate deformation independently. Instead, it shares strain with neighboring faults, promotes along-strike linkage and transfer, and forms a critical kinematic node within the active deformation belt. Regional morphometric index studies further demonstrate that tectonic activity along active faults in eastern Eastern Anatolia is not uniformly distributed along strike. Deformation tends to concentrate at segment terminations and specific fault sections.
FIGURE 12
For the Erciş Fault, reported index ranges indicate a youthful landscape and ongoing uplift. Uplift rates increase toward the northwestern and southeastern sectors (Sağlam Selçuk and Kul, 2021). Similarly, morphotectonic indicators confirm the activity of the Iğdır Fault Zone. Greater deformation accumulation and a more pronounced uplift/incision component have been reported near the southeastern terminal segments close to Mount Ağrı (Mutlu, 2025b). For the Şemdinli–Yüksekova Fault Zone, very high tectonic activity has been identified, whereas the Başkale Fault Zone exhibits moderate activity (Mutlu, 2025a). These examples demonstrate that deformation is not evenly distributed along fault zones. Instead, it concentrates in kinematically critical sections. The multi-index evaluation conducted along the HTLF yields a comparable result. The northwestern and southeastern segments display relatively stronger tectonic influence than the central segment.
6 Conclusion
The Hasan Timur Lake Fault (HTLF) is an active right-lateral strike-slip fault within the Eastern Anatolian strike-slip deformation belt, exerting a clear structural control on both drainage organization and topography. The multi-index morphometric analysis conducted on 78 fault-controlled micro-basins (HI/HE, AF, SL, Smf, and Vf) demonstrates that tectonic activity is not uniformly distributed along strike. The composite basin classification based on AF and HI indicates that high tectonic class basins are concentrated near the fault trace and at segment terminations. This spatial pattern reveals a segment-controlled deformation regime and suggests relatively stronger uplift and/or tilting components in specific sectors. Vf results show that narrow and deeply incised valleys are clustered within particular segments, indicating spatial variability in vertical incision. High SL anomalies occurring within contrasting lithologic strength classes further demonstrate that channel gradient and incision are primarily controlled by tectonic forcing rather than lithology alone. Smf values indicate that the mountain front largely preserves a linear geometry, supporting the persistence of tectonic activity along the fault. Meteorological data indicate broadly similar climatic conditions across the study area. However, the systematic alignment of morphometric variations with fault segments suggests that the observed drainage and topographic organization are predominantly governed by tectonic and lithologic controls rather than climatic forcing. At the regional scale, the HTLF occupies a transfer position within the Lake Van–Lake Urmia strike-slip deformation corridor. It shares strain with adjacent fault zones and facilitates along-strike stress transfer, constituting a critical kinematic node within the active deformation network. Overall, the integrated multi-index approach confirms that the HTLF is an active deformation zone characterized by segment-scale variability in tectonic influence. The northwestern and southeastern segments exhibit relatively stronger tectonic signatures compared to the central segment. These findings highlight the structural significance of the HTLF within the regional seismotectonic framework and underscore its relevance for future tectonic and seismic-hazard investigations.
Statements
Data availability statement
The original contributions presented in the study are included in the article/supplementary material, further inquiries can be directed to the corresponding author.
Author contributions
SM: Conceptualization, Data curation, Formal Analysis, Funding acquisition, Investigation, Methodology, Project administration, Resources, Software, Supervision, Validation, Visualization, Writing – original draft, Writing – review and editing.
Funding
The author(s) declared that financial support was not received for this work and/or its publication.
Conflict of interest
The author(s) declared that this work was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest.
Generative AI statement
The author(s) declared that generative AI was not used in the creation of this manuscript.
Any alternative text (alt text) provided alongside figures in this article has been generated by Frontiers with the support of artificial intelligence and reasonable efforts have been made to ensure accuracy, including review by the authors wherever possible. If you identify any issues, please contact us.
Publisher’s note
All claims expressed in this article are solely those of the authors and do not necessarily represent those of their affiliated organizations, or those of the publisher, the editors and the reviewers. Any product that may be evaluated in this article, or claim that may be made by its manufacturer, is not guaranteed or endorsed by the publisher.
References
1
AFAD (2025). Republic of Türkiye ministry of interior disaster and emergency management authority (AFAD). Available online at: https://deprem.afad.gov.tr/last-earthquakes.html (Accessed January 16, 2025).
2
AkbaşB.AkdenizN.AksayA.Altunİ. E.BalcıV.BilginerE.et al (2011). Geological Map of Türkiye (Scale 1:1,250,000), Prepared in the GIS environment by the Geological Research Department. Ankara, Türkiye.
3
AktimurH. T.İrfaY.ÖktemA.OlgunerA. (1979). Report No.: 6561.Geoscience data of Özalp and his surroundings. Ankara: General Directorate of Mineral Research & Exploration (MTA Press).
4
AmbraseysN. (2009). Earthquakes in the Mediterranean and Middle East: a multidisciplinary study of seismicity up to 1900. Cambridge University Press.
5
AteşS.MutluG.ÖzerkO. C.Çiçekİ.Karakaya GülmezF.Bulut ÜstünA.et al (2007). Report No.: 10961.Van İlinin yerbilim verileri. Ankara: General Directorate of Mineral Research and Exploration (MTA Press).
6
AvciV.SunkarM. (2023). Jeomorfik indislerle Varto Havzası’nı (Muş) denetleyen fayların göreceli tektonik aktivitesinin belirlenmesi. Gümüşhane Üniversitesi Fen Bilim. Derg.13 (4), 1046–1072. 10.17714/gumusfenbil.1288478
7
BullW. B. (2007). Tectonic geomorphology of mountains: a new approach to paleoseismology. Wiley-Blackwell, 316 p. ISBN 978-0-470-69155-7.
8
BullW. B.McFaddenL. D. (1977). “Tectonic geomorphology north and south of the garlock fault, California,” in Geomorphology in arid regions: a proceedings volume of the 8th annual geomorphology symposium. Editor DoehringD. O. (Binghamton: State University of New York), 115–138.
9
BurbankD. W.AndersonR. S. (2001). Tectonic geomorphology. 1st ed. Australia: Blackwell Science Ltd., 273. ISBN 978-0-632-04386-6.
10
ChenY. C.SungQ.ChengK. Y. (2003). Along-strike variations of morphotectonic features in the Western foothills of Taiwan: tectonic implications based on stream-gradient and hypsometric analysis. Geomorphology56 (1-2), 109–137. 10.1016/S0169-555X(03)00059-X
11
CopleyA.JacksonJ. (2006). Active tectonics of the Turkish‐Iranian plateau. Tectonics25 (6), 1–19. 10.1029/2005TC001906
12
DehbozorgiM.PourkermaniM.ArianM.MatkanA. A.MotamediH.HosseiniaslA. (2010). Quantitative analysis of relative tectonic activity in the Sarvestan area, central Zagros, Iran. Geomorphology121 (3-4), 329–341. 10.1016/j.geomorph.2010.05.002
13
DeweyJ. F.HemptonM. R.KiddW. S. F.SarogluF. A. M. C.ŞengörA. M. C. (1986). Shortening of continental lithosphere: the neotectonics of Eastern Anatolia—a young collision zone. Geol. Soc. Lond. Spec. Publ.19 (1), 1–36. 10.1144/GSL.SP.1986.019.01.01
14
El HamdouniR.IrigarayC.FernándezT.ChacónJ.KellerE. A. (2008). Assessment of relative active tectonics, southwest border of the Sierra Nevada (southern Spain). Geomorphology96 (1-2), 150–173. 10.1016/j.geomorph.2007.08.004
15
EmreÖ.DumanT. Y.OlgunŞ.ÖzalpS.ElmacıH. (2012). Data from: 1:250,000scale active fault map series of Turkey: Başkale (NJ 38-6) quadrangle. Ankara: General Directorate of Mineral Research and Exploration (MTA Press).
16
EmreÖ.DumanT. Y.ÖzalpS.ŞaroğluF.OlgunŞ.ElmacıH.et al (2018). Active fault database of Turkey. Bull. Earthq. Eng.16 (8), 3229–3275. 10.1007/s10518-016-0041-2
17
EyidoğanH.GüçlüU.UtkuZ.DeğirmenciE. (1991). Macro seismic guide for large Turkey earthquakes 1900-1988. İstanbul: İstanbul Technical University, Faculty of Mine, Department of Geophysics, 198.
18
GiaconiaF.Booth-ReaG.Martínez-MartínezJ. M.AzañónJ. M.Pérez-PeñaJ. V. (2012). Geomorphic analysis of the Sierra Cabrera, an active pop-up in the constrictional domain of conjugate strike-slip faults: the Palomares and Polopos fault zones (eastern betics, SE Spain). Tectonophysics580, 27–42. 10.1016/j.tecto.2012.08.028
19
GiamboniM.WetzelA.SchneiderB. (2005). Geomorphic response of alluvial rivers to active tectonics: example from the southern Rhine Graben. Aust. J. Earth Sci.97, 24–37.
20
GordonR. G. (1998). The plate tectonic approximation: plate nonrigidity, diffuse plate boundaries, and global plate reconstructions. Annu. Rev. Earth Planet. Sci.26 (1), 615–642. 10.1146/annurev.earth.26.1.615
21
GuoL.HeZ.LiL. (2023). Responses of stream geomorphic indices to piedmont fault activity in the Northern segment of the red river fault zone. Remote Sens.15 (4), 988. 10.3390/rs15040988
22
GürbüzA.ŞaroğluF. (2019). Right-lateral strike-slip faulting and related basin formations in the Turkish–Iranian plateau. Dev. Struct. Geol. Tect.3, 101–130. 10.1016/B978-0-12-815048-1.00007-X
23
HackJ. T. (1973). Stream-profile analysis and stream-gradient index. J. Res. Us Geol. Surv.1 (4), 421–429.
24
HanK.LiuD.YushanA.ShiW.LiJ.KongX.et al (2025). Study on lithospheric tectonic features of tianshan and adjacent regions and the genesis mechanism of the Wushi Ms7. 1 earthquake. Remote Sens.17 (15), 2655. 10.3390/rs17152655
25
HareP. W.GardnerT. W. (1985). Geomorphic indicators of vertical neotectonism along converging plate margins, Nicoya Peninsula, Costa Rica. Tecton. Geomorphol.4, 75–104.
26
KellerE. A.PinterN. (2002). Active tectonics: earthquakes, uplift, and landscape, Publisher. New Jersey: Prentice Hall, 362.
27
KhalifaA.CakirZ.OwenL.KayaŞ. (2018). Morphotectonic analysis of the East Anatolian fault, Turkey. Turkish J. Earth Sci.27 (2), 110–126. 10.3906/yer-1707-16
28
KoçyiğitA. (2013). New field and seismic data about the intraplate strike-slip deformation in Van region, East Anatolian plateau, E. Turkey. J. Asian Earth Sci.62, 586–605. 10.1016/j.jseaes.2012.11.008
29
MatpayB. (2024). Geomorphology and geomorphometric characteristics of Çaybaği (Kotur) Basin (Saray-Van). Amasya Üniversitesi Sos. Bilim. Derg.9 (16), 230–272. Available online at: https://izlik.org/JA35PS47RC.
30
MerrittsD.VincentK. R. (1989). Geomorphic response of coastal streams to low, intermediate, and high rates of uplift, Medocino triple junction region, northern California. Geol. Soc. Am. Bull.101 (11), 1373–1388. 10.1130/0016-7606(1989)101<1373:GROCST>2.3.CO;2
31
MutluS. (2022). Paleosismological features and segmentation of the Lake Balık fault Zone. (doctoral dissertation).Van Yüzüncü Yıl University, Van, Türkiye.
32
MutluS. (2025a). Tectonic geomorphology of the şemdinli Yüksekova Fault Zone (SYFZ) and Başkale Fault Zone (BFZ) (SE Turkey): evidence from morphometric analysis and neotectonic structures. Geol. Acta23, 1–27. 10.1344/GeologicaActa2025.23.23
33
MutluS. (2025b). The significance and morphotectonic features of the Iğdır fault within the Eastern Anatolian compressional tectonic block. Geol. Bull. Turk.68 (2), 225–258. 10.25288/tjb.1627676
34
MutluS.GündayU. (2024). Creating the earthquake risk map of Çaldıran (van) district center with geographic information systems and analytical hierarchy process (AHP). Yüzüncü Yıl Univ. J. Inst. Nat. Appl. Sci.29 (3), 967–984. 10.53433/yyufbed.1541330
35
OkayA. I.ZattinM.CavazzaW. (2010). Apatite fission-track data for the Miocene Arabia-Eurasia collision. Geology38 (1), 35–38. 10.1130/G30234.1
36
ÖzkaymakÇ.SözbilirH.BozkurtE.DirikK.TopalT.AlanH.et al (2011). Seismic geomorphology of October 23, 2011 Tabanlı-Van earthquake and its relation to active tectonics of East Anatolia. J. Geol. Eng.35 (2), 175–200.
37
Pérez-PeñaJ. V.AzañónJ. M.AzorA. (2009a). CalHypso: an ArcGIS extension to calculate hypsometric curves and their statistical moments. Applications to drainage basin analysis in SE Spain. Comput. and Geosciences35 (6), 1214–1223. 10.1016/j.cageo.2008.06.006
38
Pérez-PeñaJ. V.AzañónJ. M.Booth-ReaG.AzorA.DelgadoJ. (2009b). Differentiating geology and tectonics using a spatial autocorrelation technique for the hypsometric integral. J. Geophys. Res. Earth Surf.114 (F2), 1–15. 10.1029/2008jf001092
39
Pérez-PeñaJ. V.AzorA.AzañónJ. M.KellerE. A. (2010). Active tectonics in the Sierra Nevada (Betic Cordillera, SE Spain): insights from geomorphic indexes and drainage pattern analysis. Geomorphology119 (1-2), 74–87. 10.1016/j.geomorph.2010.02.020
40
PikeR. J.WilsonS. E. (1971). Elevation-relief ratio, hypsometric integral, and geomorphic area-altitude analysis. Geol. Soc. Am. Bull.82 (4), 1079–1084. 10.1130/0016-7606(1971)82[1079:ERHIAG]2.0.CO;2
41
PlanchonO.DarbouxF. (2002). A fast, simple and versatile algorithm to fill the depressions of digital elevation models. Catena46 (2-3), 159–176. 10.1016/S0341-8162(01)00164-3
42
RizzaM.VernantP.RitzJ. F.PeyretM.NankaliH.NazariH.et al (2013). Morphotectonic and geodetic evidence for a constant slip-rate over the last 45 kyr along the Tabriz fault (Iran). Geophys. J. Int.193 (3), 1083–1094. 10.1093/gji/ggt041
43
RockwellT. K.KellerE. A.JohnsonD. L. (1985). “Tectonic geomorphology of alluvial fans and mountain fronts near Ventura, California. In tectonic geomorphology,” in Proceedings of the 15th annual geomorphology symposium (Boston, MA: Allen and Unwin Publishers), 183–207.
44
Sağlam SelçukA.DüzgünM. (2017). Tectonic geomorphology of Başkale fault zone. Bull. Mineral Res. Explor.155, 33–46. 10.19111/bulletinofmre.315757
45
Sağlam SelçukA.KulA. Ö. (2021). Long‐term slip rate estimation for Erciş Fault in East anatolian compressive tectonic block from geologic and geomorphologic field evidence. Geol. J.56 (10), 5290–5310. 10.1002/gj.4237
46
ŞaroğluF.YılmazY. (1986). Doğu Anadolu’da neotektonik dönemdeki jeolojik evrim ve havza modelleri. MTA Derg.107, 73–94.
47
ŞaroğluF.EmreÖ.BorayA. (1987). Report No.: 394.Turkey's active faults and seismicity. Ankara: General Directorate of Mineral Research and Exploration (MTA Press).
48
SelbyM. J. (1980). A rock mass strength classification for geomorphic purposes: with tests from Antarctica and New Zealand. Z. für Geomorphol.24, 31–51. 10.1127/zfg/24/1984/31
49
SelçukA. S. (2016). Evaluation of the relative tectonic activity in the eastern Lake Van basin, East Turkey. Geomorphology270, 9–21. 10.1016/j.geomorph.2016.07.009
50
SelçukA. S.ErturaçM. K.NomadeS. (2016). Geology of the Çaldıran Fault, Eastern Turkey: age, slip rate and implications on the characteristic slip behaviour. Tectonophysics680, 155–173. 10.1016/j.tecto.2016.05.019
51
ŞengörA. M. C.KiddW. S. F. (1979). Post-collisional tectonics of the Turkish-Iranian plateau and a comparison with Tibet. Tectonophysics55 (3-4), 361–376. 10.1016/0040-1951(79)90184-7
52
ŞengörA. C.YazıcıM. (2020). The aetiology of the neotectonic evolution of Turkey. Mediterr. Geosci. Rev.2 (3), 327–339. 10.1007/s42990-020-00039-0
53
ŞengörA. C.ÖzerenM. S.KeskinM.SakınçM.ÖzbakırA. D.Kayanİ. (2008). Eastern Turkish high plateau as a small Turkic-type orogen: implications for post-collisional crust-forming processes in Turkic-type orogens. Earth-Science Rev.90 (1-2), 1–48. 10.1016/j.earscirev.2008.05.002
54
ShahzadF.GloaguenR. (2011a). TecDEM: a MATLAB based toolbox for tectonic geomorphology, part 1: drainage network preprocessing and stream profile analysis. Comput. and Geosciences37 (2), 250–260. 10.1016/j.cageo.2010.06.008
55
ShahzadF.GloaguenR. (2011b). TecDEM: a MATLAB based toolbox for tectonic geomorphology, part 2: surface dynamics and basin analysis. Comput. and Geosciences37 (2), 261–271. 10.1016/j.cageo.2010.06.009
56
Silva BarrosoP. G.GoyJ. L.ZazoC.BardajíT. (2003). Faulth-generated mountain fronts in southeast Spain: geomorphologic assessment of tectonic and seismic activity. Geomorphology50, 203–225. 10.1016/s0169-555x(02)00215-5
57
SRTM (2026). Data (Shuttle Radar Topography Mission). Available online at: https://opentopography.org/(Accessed November 10, 2025).
58
StrahlerA. N. (1952). Hypsometric (area-altitude) analysis of erosional topography. Geol. Society Am. Bull.63 (11), 1117–1142. 10.1130/0016-7606(1952)63[1117:HAAOET]2.0.CO;2
59
StrahlerA. N. (1957). Quantitative analysis of watershed geomorphology. Eos, Trans. Am. Geophys. Union38 (6), 913–920. 10.1029/TR038i006p00913
60
SuZ.WangE. C.HuJ. C.TalebianM.KarimzadehS. (2016). Quantifying the termination mechanism along the North Tabriz-North Mishu Fault Zone of Northwestern Iran via small baseline PS-InSAR and GPS decomposition. IEEE J. Selected Topics Applied Earth Observations Remote Sens.10 (1), 130–144. 10.1109/JSTARS.2016.2586742
61
ToksözM. N.ArpatE.ŞaroğluF. (1977). East Anatolian earthquake of 24 November 1976. Nature270 (5636), 423–425. 10.1038/270423b0
62
Turkish State Meteorological Service (TSMS) (2026). Climate data. Available online at: https://www.mgm.gov.tr (Accessed January 15, 2026).
63
WellsS. G.BullardT. F.MengesC. M.DrakeP. G.KarasP. A.KelsonK. I.et al (1988). Regional variations in tectonic geomorphology along a segmented convergent plate boundary pacific coast of Costa Rica. Geomorphology1 (3), 239–265. 10.1016/0169-555X(88)90016-5
64
WillgooseG. (1994). A statistic for testing the elevation characteristics of landscape simulation models. J. Geophys. Res. Solid Earth99 (B7), 13987–13996. 10.1029/94JB00123
65
YilmazY.ŞaroǧluF.GünerY. (1987). Initiation of the neomagmatism in East Anatolia. Tectonophysics134 (1-3), 177–199. 10.1016/0040-1951(87)90256-3
66
ZabcıC.ŞengörA. C. (2025). “Neotectonics of the anatolian scholle,” in Seismotectonics of the East Mediterranean-Red Sea region (Cham: Springer Nature Switzerland), 43–81.
67
ZorerH.AvciV. (2022). Geomorphologic evolution and morphometric analysis of the upper Basin (Güzelsu) of the Engil River (Van). Anemon Muş Alparslan Üniversitesi Sos. Bilim. Derg.10 (1), 249–271. 10.18506/anemon.889775
68
ZygouriV.KoukouvelasI. K.KokkalasS.XypoliasP.PapadopoulosG. A. (2015). The Nisi Fault as a key structure for understanding the active deformation of the NW Peloponnese, Greece. Geomorphology237, 142–156. 10.1016/j.geomorph.2013.09.001
Summary
Keywords
Eastern Anatolia tectonics, Hasan Timur Lake Fault, Lake Van, morpho-metric indices, relative tectonic activity
Citation
Mutlu S (2026) Assessment of relative tectonic activity along the Hasan Timur Lake Fault, East of Lake Van, eastern Türkiye. Front. Earth Sci. 14:1804337. doi: 10.3389/feart.2026.1804337
Received
05 February 2026
Revised
02 March 2026
Accepted
10 March 2026
Published
31 March 2026
Volume
14 - 2026
Edited by
Raj Sunil Kandregula, Pukyong National University, Republic of Korea
Updates
Copyright
© 2026 Mutlu.
This is an open-access article distributed under the terms of the Creative Commons Attribution License (CC BY). The use, distribution or reproduction in other forums is permitted, provided the original author(s) and the copyright owner(s) are credited and that the original publication in this journal is cited, in accordance with accepted academic practice. No use, distribution or reproduction is permitted which does not comply with these terms.
*Correspondence: Sacit Mutlu, sacitmutlu@yyu.edu.tr
Disclaimer
All claims expressed in this article are solely those of the authors and do not necessarily represent those of their affiliated organizations, or those of the publisher, the editors and the reviewers. Any product that may be evaluated in this article or claim that may be made by its manufacturer is not guaranteed or endorsed by the publisher.