Abstract
Introduction:
The occurrence and abundance of heavy metal resistance genes (HMRGs) in drinking water treatment plants (DWTPs) and the stages at which they occur are a global challenge due to the risk of consuming contaminated water.
Methods:
The present study identified HMRGs associated with raw water sources, treatment stages (disinfection and filtration), final treated water, and produced sludge in three DWTPs across three provinces (Gauteng, Limpopo, and Mpumalanga) in South Africa, using a shotgun metagenomic approach.
Results:
In total, five classes of heavy metals (copper, arsenic, mercury, chromate, silver) and 50 resistance genes were identified across the three DWTPs. Most of the genes were obtained from the disinfection stages of the DWTPs.
Discussion:
This genomic dataset provides valuable information on the impact of disinfection stages on the relative abundance of HMRGs in drinking water treatment processes. Additionally, the transfer of genes into the final treated water consumed by the populace is a significant human health concern.
1 Introduction
Heavy metals, known for their low molecular weight, can cause environmental and human health problems at certain concentrations (). Their accumulation in the environment is mainly due to anthropogenic activities, which are difficult to reverse. Rivers, which form the source of raw water for the drinking water treatment plants (DWTPs), are faced with the challenge of heavy metals pollution due to illegal domestic sewage disposal, industrial activities that generate wastewater containing heavy metals, metals dragged by rains into the rivers, and discharge of poorly treated water from the wastewater treatment plants (Zampieri et al., 2016; ).
The accumulation of these metals in rivers and other aquatic ecosystems alters microbial composition and activity, causing some microorganisms to develop strong resistance to heavy metals (; ). This resistance to heavy metals by microorganisms could be linked to genetic alterations, leading to the formation of heavy metal resistance genes (HMRGs) that enable them to survive in the environment (). Studies have reported HMRGs such as cadB (cadmium), chrA (chromium), pbrA (lead), MerA (mercury), and NiCoT (nickel) in bacteria and their involvement in the transport of transition metals in water treatment processes (; ).
DWTPs are responsible for producing good quality drinking water for human consumption; however, their effectiveness is linked to a variety of factors that include the quality of the raw water source, treatment processes and reagents used (; ; ). The treatment stages in DWTPs play a crucial role in the removal of microbial contaminants, antibiotic resistance genes, HMRGs, and other contaminants present in the raw water sources (). The abundance of bacteria possessing HMRGs, as well as the already released genes in the raw water source possess serious challenges to treat plants. Studies have shown that different treatment stages, especially in wastewater treatment plants, play a vital role in the removal of HMRGs (; ; ). However, limited studies have been conducted using a shotgun metagenomic approach to reveal the abundance of HMRGs in stages of DWTPs in South Africa. Hence, this current study aimed at unveiling the abundance of HMRGs present in raw water sources, treatment stages, final treated water, and produced sludge in three DWTPs in three different provinces in South Africa using a shotgun metagenomic approach. The presence of heavy HMRGs in the final treated water and produced sludge may have a potential impact on public health.
2 Materials and methods
2.1 Selected study sites
Three different Drinking Water Treatment Plants (DWTPs) from three Provinces in South Africa were chosen for this study because the sites serve large populations, especially in urban and rural areas, and provide drinking water. The DWTPsā names are coded as A (From Gauteng Province), B (from Limpopo Province), and C (from Mpumalanga Province) for confidentiality. The chosen study sites represent a large population in South Africa, especially in urban and rural areas where they provide drinking water (). In Gauteng, Limpopo, and Mpumalanga provinces, the primary raw water sources are the Vaal River and Crocodile River catchments, Luvuvhu River catchment, and Upper Olifants River catchment, respectively, where many anthropogenic activities such as urbanisation, agriculture and industries occur along the river (; ).
2.2 Sampling procedure
Replicate samples were taken from raw water sources, treatment stages (disinfection stage and filtration stage), produced sludge, and the final treated water. Sterile 1,000āÆmL bottles were used to collect water samples from the raw water sources (from the river catchments of the three plants), the treatment plants (disinfection stage, filtration stage), produced sludge, and final treated water, and were transported at 4āÆĀ°C to the laboratory for analysis within 3 to 6 h after collection. The triplicate samples represent independent random sampling events.
A total of 45 samples (5 sampling pointsāÆĆāÆ3 Plants (A, B, and C)āÆĆāÆ3 replicates on the sampling days per sampling points x 1 season) from all the sampling points. Samples were collected during the Spring of 2022 (in South Africa, the Spring falls within September, October, and November). To prevent external contamination of water samples collected from raw water sources, treatment stages (disinfection stage and filtration stage), produced sludge, and the final treated water in this study, strictly controlled procedures were employed, including the use of pre-sterilized or acid-washed sampling containers, disinfection and flushing of sampling points, and the use of clean personal protective equipment to avoid operator-induced contamination. Separate sampling tools were designated for each treatment stage, and containers were sealed immediately after collection to minimize exposure.
2.3 DNA extraction
One hundred millilitres of raw water and 1āÆL of water samples from the disinfection stage, filtration stage, and final treated water were filtered through a 0.22-μm polycarbonate membrane (purchased from Promolab Pty Ltd. T/A Separations, RSA). The risk of microbial contamination of the polycarbonate membrane filters was eliminated by using manufacturer-sterilized filters and handling them exclusively with sterile forceps inside a laminar-flow cabinet, along with autoclaved or single-use sterile filtration components. Additionally, filtration blanks were processed in parallel to verify sterility and ensure that any detectable DNA originated solely from the collected water samples. The filter papers with the collected microbial biomass were cut into small pieces and used for DNA extraction. Furthermore, 0.5āÆg of the produced sludge slurry, which contains the microbial biomass, was used for DNA extraction. DNA extraction was done (in the accredited microbiology and molecular biology laboratory in the University of South Africa) using MN-NucleoSpin DNA extraction kits (Promolab Pty Ltd. T/A Separations, RSA) following the manufacturerās instructions.
2.4 DNA quantification and library preparations
DNA was extracted from three independent sample replicates, and equal quantities (5āÆng each) of the resulting environmental DNA extracts were combined to generate a representative composite sample used for further analysis. DNA inhibitors were removed by applying extraction protocols that included inhibitor-removal chemistries, such as specialized binding resins, purification columns, and optimized washing buffers, capable of eliminating humic substances, metals, and residual disinfectants. For highly inhibitory matrices like disinfection and final sludge samples, additional clean-up steps (e.g., secondary silica-based purification or enhanced washing cycles) were used to ensure recovery of inhibitor-free DNA suitable for downstream molecular analyses. The DNA was quantified using a NanoDrop spectrophotometer (Thermo Fisher Scientific, United States), and the quality was checked on a 1.5% agarose gel. An obtained DNA with A260:A280 ratios between 1.8 and 2.0 and DNA concentrations of 20ā150āÆng/μL (according to internationally established standards for high-quality DNA, as recommended in the Thermo Fisher NanoDrop Spectrophotometer Guidelines and standard Illumina library preparation protocols) was sent to the Agricultural Research Council (ARC) Biotechnology Platform for shotgun metagenomic sequencing. The MGI DNBSEQ-G400 sequencing instrument was used by the ARC platform. The metagenomic shotgun data library was prepared using MGIEasy Universal DNA Library Prep Set V1.0 (MGI Tech Co., China). The quality control of the library was done using a QubitĀ® fluorometer (Life Technologies, Carlsbad, CA, United States), with the sequencing depth calculated to achieve five million reads. The DNA nanoball (DNB) was created by combining the pooled and circularized library, which was then loaded into a PE150 flow cell for sequencing in MGI DNBSEQ-G400 (MGI Tech Co., China) (2 Ć 150āÆbp).
2.5 Bioinformatics and visualization of sequencing data
Quality assessment of raw metagenomic shotgun sequencing (MSS) reads was performed using FastQC v1.0.0 (). Low-quality bases, ambiguous nucleotides, and sequencing adapters were removed using TrimGalore v0.6.5 (), applying a minimum average quality score threshold of Q15. To filter out human-derived reads, Kneaddata v0.11.0 was employed (). WGSA2.2 pipeline implemented in Nephele (v2.2.8) () was used to curate the raw MSS comprising the sequences under default parameters. HMRGs were identified using AMRFinderPlus (v4.2.7) (), in the WGSA2.2 pipeline implemented in Nephele (v2.2.8) using default parameters to annotate high-confidence HMRGs determinants from the assembled metagenomic sequences. Stacked bar charts were generated from the identified classes of heavy metal resistance genes using the Paleontological Statistics Software Package Version 4 (PAST 4) ().
2.6 Statistical analysis
The three provinces in this study are dissimilar in demographic, industrial, ruralāurban balance, or geological characteristics. To account for this inherent variability, the data were log10 normalized and statistical analysis was done on site-specific heavy metal metagenomes representing each province, ensuring that differences arising from urban runoff, industrial effluents, or natural mineral inputs are statistically adjusted. Heavy metal metagenomes were analyzed using one-way analysis of variance (ANOVA) with three replicates (nāÆ=āÆ3) per treatment. Statistical analysis was performed using Statistica version 12 (StatSoft Inc., Tulsa, OK, United States). Mean separation was conducted using Duncanās multiple range test at 95% significance level.
3 Results
3.1 Treatment plant a
In this plant, four classes of heavy metal resistance genes (HMRGs) have been identified. Table 1 provides a summary of the individual identified HMRGs and their HMM description in Gauteng Province. Variations in the relative abundance of HMRG classes were observed across raw water sources, treatment stages (disinfection and filtration), final treated water, and produced sludge (Figure 1). The raw water source, filtration stage, and final treated water contained both mercury and arsenic genes, with arsenic accounting for about 72, 75, and 97% of the genes, respectively. The disinfection stage contained all four heavy metal genes (mercury, arsenic, copper, and silver), with mercury accounting for about 67% of the genes. Produced sludge contained only mercury resistance genes (Figure 1A). To provide further insight into the significant impact of the treatment stages on the HMRGs, a statistical analysis that provides means separation across the sampling points was done. The mean separation showed that there was a significant difference (at p <āÆ0.05) across the sampling points (raw water source, disinfection stage, filtration stage, final treated water and produced sludge) for mercury and arsenic resistance genes, with the disinfection stage showing the highest value for both metals (Figure 1B).
Table 1
| Genes | Classes | HMM description |
|---|---|---|
| arsN1 | Arsenic | Arsinothricin resistance N-acetyltransferase ArsN1 family B |
| arsC | Arsenic | Glutaredoxin-dependent arsenate reductase |
| arsD | Arsenic | Arsenite efflux transporter metallochaperone ArsD |
| arsN2 | Arsenic | Arsenic resistance N-acetyltransferase ArsN2 |
| merP | Mercury | Mercury resistance system periplasmic binding protein MerP |
| merF | Mercury | Mercury resistance system transport protein MerF |
| merC | Mercury | Organomercurial transporter MerC |
| merA | Mercury | Mercury (II) reductase |
| merB | Mercury | Organomercurial lyase MerB |
| merD | Mercury | Mercury resistance co-regulator MerD |
| merE | Mercury | Broad-spectrum mercury transporter MerE |
| merG | Mercury | Phenylmercury resistance protein MerG |
| merR | Mercury | Mercury resistance transcriptional regulator MerR |
| merT | Mercury | Not provided |
| copS | Copper | Not provided |
| copR | Copper | Not provided |
| silS | Silver | Not provided |
| silA | Silver | Not provided |
| silB | Silver | Not provided |
| silF | Silver | Not provided |
| silC | Silver | Not provided |
| silR | Silver | Not provided |
Identified heavy metal resistance genes and the HMM description in treatment plant A (Gauteng Province).
Figure 1
3.2 Treatment plant B
Two classes of HMRGs (mercury and arsenic) were recorded for this plant. Table 2 provides a summary of the individual identified HMRGs and their HMM description in Limpopo Province. Variations in the relative abundance of the classes of HMRGs were observed across the raw water sources, treatment stages (disinfection and filtration stages), final treated water, and produced sludge, with the raw water sources recording about 86% of mercury and final treated water recording about 52% of arsenic metal (Figure 2A). In Figure 2B, the mean separation indicated a significant difference (at p <āÆ0.05) across the sampling points (raw water source, disinfection stage, filtration stage, final treated water and produced sludge) for mercury and arsenic resistance genes, with the disinfection stage showing the highest value for both metals.
Table 2
| Genes | Class | HMM description |
|---|---|---|
| merE | Mercury | Broad-spectrum mercury transporter MerE |
| merD | Mercury | Mercury resistance co-regulator MerD |
| merA | Mercury | Mercury (II) reductase |
| merF | Mercury | Mercury resistance system transport protein MerF |
| merP | Mercury | Mercury resistance system periplasmic binding protein MerP |
| merT | Mercury | Not provided |
| merC | Mercury | Organomercurial transporter MerC |
| merG | Mercury | Phenylmercury resistance protein MerG |
| merR | Mercury | Mercury resistance transcriptional regulator MerR |
| arsN1 | Arsenic | Arsinothricin resistance N-acetyltransferase ArsN1 family B |
| arsD | Arsenic | Arsenite efflux transporter metallochaperone ArsD |
| arsN2 | Arsenic | Arsenic resistance N-acetyltransferase ArsN2 |
Identified heavy metal resistance genes and the HMM description in treatment plant B (Limpopo Province).
Figure 2
3.3 Treatment plant C
Plant C recorded four classes of HMRGs (mercury, arsenic, copper, and chromate). Table 3 provides a summary of the individual identified HMRGs and their HMM description in Mpumalanga Province. Variations in the relative abundance of HMRG classes were observed across raw water sources, treatment stages (disinfection and filtration), final treated water, and produced sludge (Figure 3A). The raw water source, filtration stage, final treated water, and produced sludge contained both mercury and arsenic genes, with mercury accounting for about 65, 76, 65, and 88% of the genes, respectively. Disinfection stage contained all four heavy metal genes (mercury, arsenic, copper, and chromate), with mercury accounting for about 77% of the genes (Figure 3A). Significant difference (at p <āÆ0.05) was observed for mercury and arsenic resistance genes across the sampling points (Figure 3B). The disinfection and filtration stage showed the highest value for mercury resistance genes. For arsenic resistance genes, the disinfection stage, filtration stage, and final treated water showed the highest values (Figure 3B).
Table 3
| Genes | Class | HMM description |
|---|---|---|
| merP | Mercury | Mercury resistance system periplasmic binding protein MerP |
| merA | Mercury | Mercury (II) reductase |
| merR | Mercury | Mercury resistance transcriptional regulator MerR |
| merT | Mercury | Not provided |
| merG | Mercury | Phenylmercury resistance protein MerG |
| merF | Mercury | Mercury resistance system transport protein MerF |
| merC | Mercury | Organomercurial transporter MerC |
| mere | Mercury | Broad-spectrum mercury transporter MerE |
| merD | Mercury | Mercury resistance co-regulator MerD |
| merB | Mercury | Organomercurial lyase MerB |
| arsN2 | Arsenic | Arsenic resistance N-acetyltransferase ArsN2 |
| arsD | Arsenic | Arsenite efflux transporter metallochaperone ArsD |
| arsN1 | Arsenic | Arsinothricin resistance N-acetyltransferase ArsN1 family B |
| chrA | Chromate | Not provided |
| copR | Copper | Not provided |
| copS | Copper | Not provided |
Identified heavy metal resistance genes and the HMM description in treatment plant C (Mpumalanga Province).
Figure 3
4 Discussion
Treatment stages in DWTPs affect the waterās microbial ecology due to varying conditions (Zhao et al., 2025). Each stage of treatment has specific functions, and these functions determine the effectiveness and efficiency of the treatment in the production of quality drinking water (). In this study, the analysis focused on the disinfection stage and filtration stage, whose functions are mainly focused on the reduction/removal of microbial contaminants, resistant genes, including HMRGs, from the water undergoing treatment (; ; ; Zhao et al., 2025). Generally, our results showed that the disinfection stage of all the treatment plants contributed to the abundance of different classes of HMRGs when compared to the raw water sources. In addition, different treatment plants exhibited variations in HMRG classes, which could be attributed to anthropogenic activities around the raw water sources used by the treatment plants (Zampieri et al., 2016; ).
Differences in HMRG profiles across the raw water, filtration, and disinfection stages, the final treated water, and the produced sludge are consistent with the changing ecological conditions encountered throughout drinking water treatment (). Raw water naturally reflects site-specific watershed inputs, industrial activities, and geochemical conditions, which can shape distinct resistome profiles, as demonstrated by , who showed that metal-rich environments select for unique resistance-gene communities driven by long-term contamination pressures. During treatment, filtration concentrates biomass and associated resistance determinants into sludge, a pattern also observed by , who reported marked differences in metal-resistance gene abundance between influent and sludge fractions due to biomass accumulation and plasmid-mediated gene transfer in treatment systems. According to , filtration may fail to fully remove heavy-metal resistance genes because eDNA and mobile genetic elements can pass through filter media. Disinfection introduces strong oxidative and chemical stress that favors metal-tolerant microorganisms, similar to findings by , who noted that heavy-metal resistance genes often persist or increase after treatment because resistant taxa are selectively retained. Additional metagenomic studies, including and , further show that co-selection with antibiotic-resistance genes and enrichment of mobile genetic elements contribute to heterogeneity across treatment stages. These mechanisms collectively explain the stage-specific and plants-specific patterns of HMRGs observed in the present study.
Raw water sources are the starting point of the DWTPs, and they have different chemical and physical properties, which tend to determine the microbial constituent (Zhao et al., 2025). The nature and load of the contaminants could play a role in how the DWTPsā stages perform to ensure good quality of drinking water (). The disinfection stage, which aimed at the removal of microbial contaminants as well as the associated resistant genes present in the raw water sources, also has a challenge of releasing more resistant genes from the microbial communities (). This aligns with the findings in this current study, where, in Plant A, all four classes of HMRGs (mercury, arsenic, copper, and silver) occurred, and in Plant C, where all four classes of HMRGs (mercury, arsenic, copper, and chromium) occurred when compared to the raw water sources.
The filtration stage is essential in the treatment process because of its role in the removal of microorganisms () and antibiotic-resistant genes (). The role of the filtration stage in the removal of resistance genes was observed in this study, especially in Plant A and Plant C. In plant A, only HMRGs of mercury and arsenic were observed, indicating the removal of copper and silver during the stage. This was also evident in the final treated water. In Plant C, only HMRGs of mercury and arsenic were observed, indicating the removal of copper and chromium during the stage. This was also evident in the final treated water.
In the final treated water for all the plants, mercury resistance genes and arsenic resistance genes were dominant, with variations in the treatment plants. This is a great health concern as the final treated water is being consumed by the populace in that province. highlighted that mercury exposure could lead to heart disease. Exposure to arsenic could lead to cancer, skin disorders, and cognitive impairment, among other conditions (). Consumption of water with these resistance genes could expose humans to these diseases, as these genes can penetrate through the cell structures as well as bacteria that are normal flora to human beings and cause diseases ().
Heavy-metal exposure has been linked internationally to cancers, cardiovascular disease, neurological impairment, and skin disorders, and several South African studies highlight similar risks in provinces where this study was conducted. In Gauteng, reported elevated arsenic and lead in soils around early learning centres, noting associated risks for childhood cognitive impairment, carcinogenesis, and skin lesions. In Limpopo, identified groundwater contamination with lead and vanadium, finding both non-carcinogenic and carcinogenic risks for residents, particularly through long-term exposure pathways. Additional work by in rural Limpopo showed significant arsenic contamination linked to abandoned mining areas, emphasizing risks for skin lesions, cardiovascular effects, and reduced IQ in exposed populations. In view of this, heavy-metal exposure (including the ones from final treated water) may pose real public-health risks within these provinces.
5 Conclusion
The production of potable water of good microbiological and aesthetic status is pertinent to the health of human beings who depend on the water for drinking, domestic activities, and other activities necessary for survival. The presence of contaminants and genes in the final treated water is a drawback to the roles of the DWTPs. In this study, the disinfection stage is the contributing factor to the abundance and diversity of HMRGs, and the filtration stageās function in the removal of these genes was also minimal, as observed in the final treated water. This is a concern for the treatment plants. Studies are recommended in the development of real-time technology that can take into account the presence of these genes during the treatment stages and promote sustainable removal of these genes.
Statements
Data availability statement
All data analysis results from this study are included in the manuscript. All the raw datasets have been deposited at the NCBI database (https://www.ncbi.nlm.nih.gov/) sequence archive (SRA) as BioProject ID PRJNA1090776.
Author contributions
MT: Conceptualization, Formal analysis, Funding acquisition, Investigation, Supervision, Writing ā review & editing. CK: Data curation, Formal analysis, Validation, Writing ā original draft.
Funding
The author(s) declared that financial support was received for this work and/or its publication. The authors wish to acknowledge the Water Research Commission (South Africa) for funding under the research grant 2022/2023-00801.
Acknowledgments
The authors wish to acknowledge the University of South Africa for their support.
Conflict of interest
The author(s) declared that this work was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest.
The author MT declared that they were an editorial board member of Frontiers, at the time of submission. This had no impact on the peer review process and the final decision.
Generative AI statement
The author(s) declared that Generative AI was not used in the creation of this manuscript.
Any alternative text (alt text) provided alongside figures in this article has been generated by Frontiers with the support of artificial intelligence and reasonable efforts have been made to ensure accuracy, including review by the authors wherever possible. If you identify any issues, please contact us.
Publisherās note
All claims expressed in this article are solely those of the authors and do not necessarily represent those of their affiliated organizations, or those of the publisher, the editors and the reviewers. Any product that may be evaluated in this article, or claim that may be made by its manufacturer, is not guaranteed or endorsed by the publisher.
References
1
AndrewsS. (2010). FastQC: a quality control tool for high throughput sequence data. Available online at: https://www.bioinformatics.babraham.ac.uk/projects/fastqc/
2
AzmiL. S. (2025). Membrane filtration technologies for sustainable industrial wastewater treatment: a review of heavy metal removal. Desalin. Water Treat.:101321. doi: 10.1016/j.dwt.2025.101321
3
BorrullJ.ColomA.FabregasJ.BorrullF.PocurullE. (2021). Presence, behaviour and removal of selected organic micropollutants through drinking water treatment. Chemosphere276:130023. doi: 10.1016/j.chemosphere.2021.130023,
4
CesconA.JiangJ.-Q. (2020). Filtration process and alternative filter media material in water treatment. Water12:3377. doi: 10.3390/w12123377
5
ChenQ. Y.CostaM. (2021). Arsenic: a global environmental challenge. Annu. Rev. Pharmacol. Toxicol.61, 47ā63. doi: 10.1146/annurev-pharmtox-030220-013418
6
DaiZ.Sevillano-RiveraM. C.CalusS. T.de Bautista-los SantosQ. M.ErenA. M.van der WielenP. W. J. J.et al. (2020). Disinfection exhibits systematic impacts on the drinking water microbiome. Microbiome8:42. doi: 10.1186/s40168-020-00813-0,
7
DasS.DashH. R.ChakrabortyJ. (2016). Genetic basis and importance of metal resistant genes in bacteria for bioremediation of contaminated environments with toxic metal pollutants. Appl. Microbiol. Biotechnol.100, 2967ā2984. doi: 10.1007/s00253-016-7364-4,
8
DWS (2022). National Assembly: Minister of Water and Sanitation Written Reply to Question 19. Department of Water and Sanitation, Republic of South Africa. Available online at: https://www.dws.gov.za/Projects/National%20State%20of%20Water%20Report/Documents/National%20State%20of%20Water%20Report%202022.pdf (Accessed June 29, 2025).
9
EllwangerJ. H.ZiliottoM.ChiesJ. A. B. (2025). Toxicogenomics of arsenic, lead and mercury: the toxic triad. Pollutants5:18. doi: 10.3390/pollutants5030018
10
EnahoroJ. A. (2025). Integrating metagenomics in environmental monitoring: co-selection of heavy metal and antimicrobial resistance genes in contaminated aquatic systems. IJISRT10, 1571ā1575. doi: 10.38124/ijisrt/25aug910
11
FeldgardenM.BroverV.Gonzalez-EscalonaN.FryeJ. G.HaendigesJ.HaftD. H.et al. (2019). AMRFinderPlus and the reference gene Catalog facilitate detection of antimicrobial resistance genes in bacterial whole-genome sequences. Microb. Genom.5:e000513. doi: 10.1038/s41598-021-91456-0
12
FengJ.ZhouL.ZhaoX.ChenJ.LiZ.LiuY.et al. (2023). Evaluation of environmental factors and microbial community structure in an important drinking-water reservoir across seasons. Front. Microbiol.14:1091818. doi: 10.3389/fmicb.2023.1091818,
13
GaoL.HuangY.LiuY.MohamedO. A. A.FanX.WangL.et al. (2022). Bacterial community structure and potential microbial coexistence mechanism associated with three halophytes adapting to the extremely hypersaline environment. Microorganisms10:1124. doi: 10.3390/microorganisms10061124,
14
GenchiG.SinicropiM. S.CarocciA.LauriaG.CatalanoA. (2017). Mercury exposure and heart diseases. Int. J. Environ. Res. Public Health14:74. doi: 10.3390/ijerph14010074,
15
GuptaP.DiwanB. (2017). Bacterial exopolysaccharide-mediated heavy metal removal: a review on biosynthesis, mechanism and remediation strategies. Biotechnol. Rep.13, 58ā71. doi: 10.1016/j.btre.2016.12.006,
16
GuptaS. K.ShinH.HanD.HurH. G.UnnoT. (2018). Metagenomic analysis reveals the prevalence and persistence of antibiotic-and heavy metal-resistance genes in wastewater treatment plant. J. Microbiol.56, 408ā415. doi: 10.1007/s12275-018-8195-z,
17
HammerĆ.HarperD. A. (2001). PAST: paleontological statistics software for education and data analysis. Palaeontol. Electron., 4:9. Available online at: http://palaeo-electronica.org/2001_1/past/issue1_01.htm (Accessed February 9, 2026).
18
HemmeC. L.DengY.GentryT. J.FieldsM. W.WuL.BaruaS.et al. (2010). Metagenomic insights into evolution of a heavy metal-contaminated groundwater microbial community. ISME J.4, 660ā672. doi: 10.1038/ismej.2009.154,
19
Huttenhower Lab (2018). KneadData: Quality Control and Filtering Tool for Metagenomic Data. Available online at: https://huttenhower.sph.harvard.edu/kneaddata/ (Accessed December 12, 2025).
20
JanssenP. J.Van HoudtR.MoorsH.MonsieursP.MorinN.MichauxA.et al. (2010). The complete genome sequence of Cupriavidus metallidurans strain CH34, a master survivalist in harsh and anthropogenic environments. PLoS One5:e10433. doi: 10.1371/journal.pone.0010433,
21
JiaS.BianK.ShiP.YeL.LiuC. H. (2020). Metagenomic profiling of antibiotic resistance genes and their associations with bacterial community during multiple disinfection regimes in a full-scale drinking water treatment plant. Water Res.176:115721. doi: 10.1016/j.watres.2020.115721,
22
KapwataT.MatheeA.SweijdN.MinakawaN.MogotsiM.KuneneZ.et al. (2020). Spatial assessment of heavy metals contamination in household garden soils in rural Limpopo Province, South Africa. Environ. Geochem. Health42, 4181ā4191. doi: 10.1007/s10653-020-00535-0,
23
KootbodienT.MkunyanaY.NelM.MahlangeniN.StreetR. (2026). Assessment of soil metal exposure, associated health risks and indoor dust screening in early learning programmes in Gauteng Province, South Africa. Environ. Geochem. Health48:136. doi: 10.1007/s10653-026-03034-w,
24
KruegerF. (2015). TrimGalore: a wrapper tool around Cutadapt and FastQC to consistently apply quality and adapter trimming. Available online at: https://www.bioinformatics.babraham.ac.uk/projects/trim_galore/ (Accessed December 12, 2025).
25
LiA. D.LiL. G.ZhangT. (2015). Exploring antibiotic resistance genes and metal resistance genes in plasmid metagenomes from wastewater treatment plants. Front. Microbiol.6:1025. doi: 10.3389/fmicb.2015.01025,
26
LiuX.WangC.WangW.QiuY.TangY.WangC.et al. (2025). Combined pollution of heavy metals and polycyclic aromatic hydrocarbons in non-ferrous metal smelting wastewater treatment plant: distribution profiles, removal efficiency, and ecological risks to receiving river. J. Hazard. Mater.486:137118. doi: 10.1016/j.jhazmat.2025.137118
27
MaX.VikramA.CassonL.BibbyK. (2017). Centralized drinking water treatment operations shape bacterial and fungal community structure. Environ. Sci. Technol.51, 7648ā7657. doi: 10.1021/acs.est.7b00768,
28
MalieheT. S.MavingoN.SelepeT. N.MasokoP.MashaoF. M.NyamutswaN. (2024). Quantitative assessment of human health risks associated with heavy metal and bacterial pollution in groundwater from Mankweng in Limpopo Province, South Africa. Int. J. Environ. Res. Public Health21:1489. doi: 10.3390/ijerph21111489,
29
Mensah-AkuttehH.BuamahR.WiafeS.NyarkoK. B. (2022). Raw water quality variations and its effect on the water treatment processes. Cogent Eng.9:2122152. doi: 10.1080/23311916.2022.2122152
30
MoreiraV. R.MoserP. B.GuimaraesR. N.AmaralM. C. (2025). Ultrafiltration and reverse osmosis integrated to conventional drinking water treatment to ensure human right to water in dam break scenarios: from bench-to pilot-scale. Sep. Purif. Technol.353:128429. doi: 10.1016/j.seppur.2024.128429
31
NaccacheC.IbrahimC.HassenA.KhemakhemM. M. (2025). Metagenomics-based analysis of mobile genetic elements and antibiotic/metal resistance genes carried by treated wastewater. PeerJ13:e19682. doi: 10.7717/peerj.19682,
32
NakazawaY.AbeT.MatsuiY.ShinnoK.KobayashiS.ShirasakiN.et al. (2021). Differences in removal rates of virgin/decayed microplastics, viruses, activated carbon, and kaolin/montmorillonite clay particles by coagulation, flocculation, sedimentation, and rapid sand filtration during water treatment. Water Res.203:117550. doi: 10.1016/j.watres.2021.117550,
33
PangH.BenY.CaoY.QuS.HuC. (2025). Time series-based machine learning for forecasting multivariate water quality in full-scale drinking water treatment with various reagent dosages. Water Res.268:122777. doi: 10.1016/j.watres.2024.122777,
34
PollardA. I.HamptonS. E.LeechD. M. (2018). The promise and potential of continental-scale limnology using the US Environmental Protection Agency's National Lakes Assessment. Limnol. Oceanogr. Bull.27, 36ā41. doi: 10.1002/lob.10238.
35
SantanaM. V. E.ZhangQ.MihelcicJ. R. (2014). Influence of water quality on the embodied energy of drinking water treatment. Environ. Sci. Technol.48, 3084ā3091. Available online at: https://pubs.acs.org/doi/full/10.1021/es404300y?src=recsys,
36
SharmaS. (2012). Bioremediation: features, strategies and applications. Asian J. Pharm. Life Sci.2, 202ā213. Available online at: http://ajpls.org/admin/Issues/PIssue172.pdf
37
ShuklaA.ShuklaA.ShuklaP. K. (2025). āRole of biotechnology in wastewater treatment: an overview,ā in Biotechnology Approaches to Industrial and Pharmaceutical Wastewater Treatment, (Hershey, PA, USA: IGI Global), 1ā32.
38
TiwariA.Gomez-AlvarezV.SiponenS.SarekoskiA.HokajarviA.KappinenA.et al. (2022). Bacterial genes encoding resistance against antibiotics and metals in well-maintained drinking water distribution systems in Finland. Front. Microbiol.12:803094. doi: 10.3389/fmicb.2021.803094
39
WeberN.LiouD.DommerJ.MacMenaminP.QuiƱonesM.MisnerI.et al. (2018). Nephele: a cloud platform for simplified, standardized and reproducible microbiome data analysis. Bioinformatics34, 1411ā1413. doi: 10.1093/bioinformatics/btx617,
40
XavierJ. C.CostaP. E. S.HissaD. C.MeloV. M. M.FalcĆ£oR. M.BalbinoV. Q.et al. (2019). Evaluation of the microbial diversity and heavy metal resistance genes of a microbial community on contaminated environment. Appl. Geochem.105, 1ā6. doi: 10.1016/j.apgeochem.2019.04.012
41
XuL.OuyangW.QianY.SuC.SuJ.ChenH. (2016). High-throughput profiling of antibiotic resistance genes in drinking water treatment plants and distribution systems. Environ. Pollut.213, 119ā126. doi: 10.1016/j.envpol.2016.02.013,
42
ZampieriB.DelB.PintoA. B.SchultzL.OliveiraM. A.de OliveiraA. J. F. C. (2016). Diversity and distribution of heavy metal-resistant bacteria in polluted sediments of the AraƧa Bay, SĆ£o SebastiĆ£o (SP), and the relationship between heavy metals and organic matter concentrations. Microb. Ecol.72, 582ā594. doi: 10.1007/s00248-016-0732-2
43
ZhaoZ.SunW.KeY.ZhangY.WangX. (2025). Microbial dynamics at different stages of drinking water treatment systems. Environ. Sci. Water Res. Technol.11, 1401ā1427. doi: 10.1039/d4ew00972j
Summary
Keywords
disinfection, drinking water, final treated water, heavy metal, raw water sources, resistance genes, shotgun metagenomics
Citation
Tekere M and Kalu CM (2026) Relative abundance of heavy metal resistance genes of three drinking water treatment plants unveiled through shotgun metagenomics. Front. Microbiol. 17:1822428. doi: 10.3389/fmicb.2026.1822428
Received
03 March 2026
Revised
31 March 2026
Accepted
06 April 2026
Published
21 April 2026
Volume
17 - 2026
Edited by
Issmat I. Kassem, University of Georgia, United States
Reviewed by
Bekir Kocazeybek, Istanbul University-Cerrahpasa, Türkiye
Eman A. Muhsin, Republic of Iraq Ministry of Higher Education and Scientific Research, Iraq
Updates
Copyright
Ā© 2026 Tekere and Kalu.
This is an open-access article distributed under the terms of the Creative Commons Attribution License (CC BY). The use, distribution or reproduction in other forums is permitted, provided the original author(s) and the copyright owner(s) are credited and that the original publication in this journal is cited, in accordance with accepted academic practice. No use, distribution or reproduction is permitted which does not comply with these terms.
*Correspondence: Chimdi Mang Kalu, kaluchimdimang@yahoo.com
Disclaimer
All claims expressed in this article are solely those of the authors and do not necessarily represent those of their affiliated organizations, or those of the publisher, the editors and the reviewers. Any product that may be evaluated in this article or claim that may be made by its manufacturer is not guaranteed or endorsed by the publisher.