Abstract
We propose a theoretical propulsion architecture in which the Casimir effect drives a mechanical see-saw oscillator that repeatedly impacts piezoelectric crystals, converting the resulting mechanical energy into electrical current. This harvested current is stored and used to power a magnetoplasmadynamic (MPD) thruster for interstellar space propulsion. The see-saw mechanism addresses a fundamental challenge of Casimir-piezoelectric harvesting: the piezoelectric effect requires changing mechanical strain, not static force, to produce continuous current. By alternating the Casimir-driven collapse of opposing plates onto piezoelectric elements, the architecture produces a repeatable cycle of charge generation. Onboard waste heat from the spacecraft’s radioisotope thermoelectric generator (RTG) provides the external energy input via thermal expansion of the see-saw beam, resetting the Casimir gaps after each impact; the Casimir force serves as the closing mechanism rather than the energy source. Temperature additionally serves a regulatory role via thermal corrections to optimize oscillation characteristics. Scaled across a large array of nanoscale Casimir gaps at the aft of the spacecraft, this framework is proposed as a candidate supplementary high-specific-impulse electric propulsion concept for interstellar missions. We outline the theoretical chain, present order-of-magnitude scaling analysis, identify key open questions and scaling constraints, and propose directions for future work. Experimental work has validated that piezoelectric elements can detect and respond to Casimir-scale forces, supporting the physical basis of this architecture. The architecture provides continuous supplementary MPD thrust for the operational lifetime of the onboard reactor without drawing from the primary power budget, limited only by propellant supply.
1 Introduction
Conventional propulsion systems are fundamentally limited by propellant mass requirements. Advanced concepts such as nuclear thermal, nuclear electric, and antimatter propulsion offer significant improvements in specific impulse but remain constrained by fuel storage and energy conversion challenges. For interstellar missions, where distances render chemical and even nuclear-thermal propulsion impractical, novel energy harvesting and conversion mechanisms warrant theoretical investigation.
The Casimir effect, an attractive force arising from quantum vacuum fluctuations between closely spaced conducting plates, has been proposed as a basis for energy harvesting in various forms (; ). Prior work has explored harvesting energy from Casimir-scale forces via piezoelectric transduction, including proposed Casimir-piezoelectric generator designs (; ; ). More broadly, recent advances in piezoelectric energy harvesting-including high-performance composite materials () and programmable ferroelectric nanocomposites () - have demonstrated continued improvements in conversion efficiency and miniaturization, further motivating investigation of piezoelectric transduction mechanisms for novel energy recovery applications. A recurring feature of Casimir-piezoelectric proposals is the framing of the quantum vacuum as a net energy source. We take a deliberately different position: the Casimir force is conservative, and the energy accounting of any proposed harvesting cycle must be rigorously examined. This work focuses on the mechanical architecture of energy conversion rather than claiming net energy extraction from the vacuum. The proposed system is thermodynamically a waste-heat engine: onboard waste heat provides the energy input via thermal expansion of the oscillator beam, the Casimir force serves as the mechanical closing mechanism (analogous to a spring in a conventional engine), and the cold of deep space serves as the thermal sink. The energy source is unambiguously the spacecraft’s waste heat, not the quantum vacuum.
demonstrated that piezoelectric tuning forks can make precision measurements of Casimir-scale forces, establishing experimentally that piezoelectric elements respond to forces in this regime. We build on this experimental foundation to propose a mechanical harvesting architecture: a see-saw oscillator that converts the Casimir-driven plate collapse into repeatable piezoelectric impacts (Figure 1).
FIGURE 1
To our knowledge, the coupling of a Casimir-driven piezoelectric harvesting mechanism to a magnetoplasmadynamic (MPD) propulsion stage has not been previously proposed. This paper introduces that architecture, which we term the Casimir Piezoelectric Drive (CPD), as a theoretical framework and identifies the key physics and engineering questions that must be resolved before feasibility can be assessed.
2 Theoretical framework
2.1 The casimir effect
The Casimir effect arises from quantum vacuum fluctuations of the electromagnetic field between two closely spaced conducting plates. The attractive force per unit area between two ideal, perfectly conducting parallel plates is given by:where is the plate separation, is the reduced Planck constant, and is the speed of light. At nanoscale separations (– nm), this force becomes mechanically significant-sufficient to produce measurable deflection in micro- and nano-mechanical structures.
The force scales as , meaning it increases rapidly as the gap narrows. This strong distance dependence is central to the proposed architecture: as the see-saw brings a plate closer to its opposing surface, the Casimir attraction accelerates the closure, delivering a mechanical impact to the piezoelectric element ().
2.2 The see-saw mechanism
A fundamental challenge in Casimir-piezoelectric energy harvesting is that the piezoelectric effect generates current only in response to changing mechanical strain (), not static stress. A constant Casimir force produces only a single transient charge displacement, not continuous power. Any viable harvesting architecture must therefore produce a repeatable mechanical cycle.
We propose a see-saw oscillator mechanism to achieve this. The architecture consists of:
A metal plate mounted on a central pivot, forming a see-saw (lever arm).
Piezoelectric crystals positioned beneath each end of the see-saw.
Casimir-active surfaces (closely spaced conducting plates) at each end, such that the Casimir attractive force acts to pull each end downward toward its respective piezoelectric crystal.
The operating cycle proceeds as follows:
Half-cycle A: The Casimir force on side A pulls that end of the see-saw downward. As the gap narrows, the scaling accelerates the closure. Side A impacts the piezoelectric crystal beneath it, generating a pulse of electrical current from the mechanical impact. At contact, the Casimir gap on side A is effectively zero and the Casimir force on that side ceases to drive further motion.
Half-cycle B: With side A at rest on its crystal, the Casimir force on side B (where the gap is now maximal due to the see-saw geometry) pulls side B downward. The lever arm lifts side A away from its crystal, reopening the Casimir gap on side A. Side B impacts its piezoelectric crystal, generating another pulse of current.
The cycle then repeats: the see-saw alternates between sides, with each impact generating a current pulse. The see-saw geometry ensures that the closure of one gap necessarily reopens the other, creating a self-resetting mechanical cycle.
Whether the see-saw geometry permits net positive energy extraction despite the conservative nature of the Casimir force is the central open question of this architecture and is addressed in Section 4.3.
A key reliability concern for the seesaw mechanism is stiction: at nanoscale separations, Casimir and van der Waals forces can cause permanent adhesion of the plates upon contact, a well-characterized failure mode in NEMS devices. Several mitigation strategies from the NEMS literature are applicable to this geometry. Anti-stiction surface coatings, including self-assembled monolayers (SAMs) and fluoropolymer films, reduce adhesion energy by lowering surface energy at the contact interface. Dimpled or textured contact surfaces reduce the real contact area and correspondingly reduce adhesion forces. Operating the seesaw at amplitudes above the critical pull-in threshold (typically one-third of the initial gap for electrostatic actuators) can prevent snap-in instability, though the Casimir force’s scaling modifies this threshold relative to the electrostatic case. Material selection also plays a role: harder contact surfaces resist plastic deformation that increases real contact area over repeated impact cycles. The thermal expansion reset mechanism provides an additional advantage, as the reset force (estimated at from the beam’s thermal stress, compared to Casimir attraction at ) provides a substantial margin for overcoming adhesion at contact. Quantitative assessment of stiction probability under the specific impact conditions of the seesaw (impact velocity , contact area ) remains an open question requiring experimental investigation.
2.3 Energy storage
The current pulses generated by the piezoelectric impacts are collected and stored in a capacitive storage system positioned beneath the reaction assembly, within the vacuum environment. This stored electrical energy accumulates over many cycles and serves as the power source for the MPD thruster. The storage system must accommodate the pulsed nature of the piezoelectric output and deliver steady power to the thruster stage during each burst. This operational mode-pulsed energy accumulation followed by brief, high-power discharge-is well-established in electric propulsion: pulsed plasma thrusters (PPTs) routinely operate from capacitor-discharge circuits that accumulate energy over milliseconds to seconds and discharge in microseconds (; ). The CPD architecture extends this principle to longer accumulation periods (on the order of minutes) matched to the lower power output of the harvesting array. Power conditioning electronics between the storage bank and the thruster regulate voltage and current delivery to match the MPD operating requirements.
2.4 Waste heat as the external energy input
The see-saw mechanism requires an external energy source to reset the Casimir gaps after each impact, as the conservative nature of the Casimir force precludes net energy extraction from the closing-reopening cycle alone. We propose that onboard waste heat provides this energy via thermal expansion of the see-saw beam structure.
Any interstellar spacecraft must carry an onboard power source (typically a radioisotope thermoelectric generator (RTG), or a nuclear reactor for higher-power missions) since solar power is unavailable at interstellar distances. RTGs are the only flight-proven electrical power source for deep-space missions beyond Jupiter, with demonstrated operational lifetimes exceeding 40 years (Voyager 1 and 2). These power systems inherently produce substantial waste heat: an RTG producing 250 W of electrical power simultaneously generates approximately 3,750 W of waste heat, which is conventionally radiated into space without recovery.
The proposed mechanism operates as follows: waste heat conducted through the spacecraft structure into the see-saw beam causes thermal expansion of the beam material. For an aluminum beam (thermal expansion coefficient 23 × 10−6/K) of length ∼80 μm, a temperature swing of 50 K produces approximately 90 nm of displacement-sufficient to reopen the Casimir gap from contact to maximum separation. As the beam cools (radiating to the ∼2.7 K background of deep space), the Casimir attractive force closes the gap, driving the impact on the piezoelectric crystal.
The system thus operates as a heat engine: the hot reservoir is the spacecraft’s waste heat, the working mechanism is the thermal expansion/ Casimir contraction cycle driving piezoelectric transduction, and the cold reservoir is space itself. The conversion is bounded by the Carnot efficiency set by the temperature differential between the spacecraft and the space environment.
Critically, the waste heat is energy the spacecraft produces regardless of whether the Casimir-piezoelectric array is present. The architecture therefore provides supplementary thrust from energy that would otherwise be lost to radiation, without drawing from the spacecraft’s primary electrical power budget. Temperature additionally serves a regulatory role: by modulating the thermal environment of the Casimir gaps via thermal () corrections, the oscillation characteristics can be tuned to optimize harvesting performance.
The thermal pathway from the onboard power source to the seesaw array proceeds via conduction through the spacecraft structure, following established spacecraft thermal management practice. RTG-equipped missions routinely manage waste heat distribution across the spacecraft bus: Voyager 1 and 2, Cassini, and New Horizons all employ radioisotope waste heat for thermal regulation of onboard subsystems via conductive and radiative coupling. The array substrate, onto which the seesaw units are fabricated, is thermally coupled to the spacecraft’s primary thermal bus-a network of heat pipes or conductive struts that distributes waste heat from the RTG throughout the spacecraft. At practical array scales (N ∼ 106), the required thermal input is approximately 1 W (Section 4.5), representing less than 0.03% of the waste heat budget of a single 250 W-class RTG. During the heating phase of each cycle, waste heat conducted through the substrate into the beam’s pivot mount propagates to the beam tips with a thermal equilibration time of approximately for an aluminum beam of half-length (see Section 4.2). During the cooling phase, the substrate serves as a relative heat sink as it re-equilibrates with the spacecraft’s radiator panels. Active thermal modulation of the substrate temperature-for example, via thermoelectric elements at the substrate-bus interface-could enable controlled cycling at rates matched to the seesaw’s mechanical response time, though the engineering feasibility of such modulation at the required frequencies () remains an open question.
2.5 MPD propulsion
Magnetoplasmadynamic (MPD) propulsion accelerates ionized propellant via the Lorentz force J × B (), where J is the current density driven through the plasma and B is the applied magnetic field. MPD thrusters are characterized by high specific impulse and are well-suited to the low-thrust, high-efficiency regime required for interstellar missions. Recent experimental progress has demonstrated MPD operation at propulsion-relevant power levels: in February 2026, NASA’s Jet Propulsion Laboratory successfully tested a lithium-fed MPD thruster at 120 kW, more than 25 times the power of current flight electric propulsion systems (), with near-term scaling targets of 500 kW to 1 MW per thruster. Although no MPD thruster has yet flown a space mission, these ground demonstrations establish the technology readiness trajectory for the propulsion stage assumed in this architecture.
Given sufficient electrical power from the Casimir-piezoelectric harvesting and storage stage, an MPD thruster can generate continuous thrust. The MPD stage is a well-characterized propulsion technology; the novel contribution of this work lies in the upstream energy harvesting mechanism, not the thruster itself. It is important to emphasize that the Casimir-piezoelectric array and the MPD thruster are physically and functionally separate subsystems. The nanoscale Casimir gaps (–) exist within the seesaw array, which serves exclusively as an electrical power source. The MPD thruster operates at its conventional electrode geometry (inter-electrode spacing on the order of millimeters) and receives electrical power from the capacitive storage bank via standard power conditioning electronics. The Casimir effect plays no role in the thruster’s plasma acceleration physics; it functions solely within the upstream harvesting stage.
In the proposed architecture, the MPD thruster does not operate continuously but in burst mode: the capacitive storage system accumulates charge from the piezoelectric array over many cycles until sufficient energy has been stored to fire the thruster. The thruster then operates for a brief interval, expending the stored energy, before returning to accumulation mode. In the zero-drag environment of interstellar space, each velocity increment produced by a thruster burst is permanently retained, and the spacecraft’s velocity increases monotonically over time. This operational mode also provides the capability for trajectory course corrections as needed during the interstellar coast phase.
2.6 The complete chain
The proposed architecture operates as a six-stage energy conversion chain (Figure 2).
FIGURE 2
The system is scaled across see-saw units distributed across the aft surface of the spacecraft. Onboard waste heat provides the external energy input that drives the cycle, while temperature additionally serves a regulatory role via thermal (Lifshitz) corrections to the Casimir force.
3 Experimental foundation
designed a quantum field energy sensor based on the Casimir effect, using piezoelectric quartz tuning forks to make precision measurements of Casimir forces. The tuning forks exhibited sub-millihertz frequency stability over 12-h periods, and spring constants ranging from 1,200 N/m to 42 kN/m were characterized across different tuning fork geometries.
While Ludwig’s experimental parameters (spring constants of 1,200–42,000 N/m, sub-millihertz frequency stability) were optimized for force measurement rather than energy harvesting, the demonstrated sensitivity of piezoelectric elements to Casimir-scale forces supports the physical basis of the harvesting stage proposed here. Optimal parameters for energy harvesting (including plate geometry, gap size, and piezoelectric material selection) remain to be determined and are identified as future work.
4 Scaling considerations
4.1 Single-unit force and energy
From the Casimir force expression, the attractive pressure between two ideal parallel conducting plates is:
At a plate separation of nm with plate area :
The force per gap is then:
At nm, the scaling yields:
This 10,000× force differential between nm and nm is central to the see-saw energy balance discussed in Section 2.2.
The energy harvested per impact is obtained by integrating the Casimir force over the gap closure from to :
Substituting nm, nm, m2:
A full see-saw cycle comprises two impacts, yielding:
4.2 Oscillation frequency analysis
The scaling calculations in Section 4.3 require a physically justified operating frequency for the seesaw cycle. We derive this from the mechanical dynamics of the seesaw and the thermal timescale of the reset phase.
4.2.1 Effective mass
For a uniform beam of mass pivoting at its center, the moment of inertia is . The effective translational mass at the tip is:
With , , , :
4.2.2 Equation of motion
The seesaw geometry couples the two Casimir gaps: when the tip is displaced a distance past the equilibrium point , the closing-side gap is and the opening-side gap is . The net force on the tip is:
At , the net force vanishes—the equilibrium is unstable, analogous to an inverted pendulum. Any perturbation past produces a net force that accelerates the seesaw toward impact.
4.2.3 Characteristic mechanical timescale
Linearizing about the equilibrium:
The instability growth rate is:corresponding to a characteristic mechanical frequency of . Numerical integration of the full nonlinear equation of motion yields Casimir-driven fall times of 1–4 from perturbation to impact (), depending on the magnitude of the initial perturbation provided by the thermal reset. The terminal impact velocity converges to approximately 0.35 m/s independent of the initial perturbation, as the kinetic energy is dominated by the strong force in the final nanometers of closure.
4.2.4 Thermal reset timescale
As established in Section 2.4, waste heat provides the energy to reset the Casimir gap via thermal expansion. The rate-limiting step is the thermal transport time from the heat source (at the pivot/substrate interface) to the beam tips. For aluminum, the thermal diffusivity is . The conductive equilibration time over the beam half-length is:
By contrast, radiative cooling of the beam (surface area ) to the 2.7 K deep-space background yields a thermal time constant of approximately 0.65 m—three orders of magnitude slower. Conductive thermal cycling through the substrate is therefore required for high-frequency operation; the array substrate must be thermally coupled to both a heat source (waste heat from the RTG) and a heat sink to enable rapid temperature cycling of the beam.
4.2.5 Resulting frequency estimate
A full seesaw cycle comprises two half-cycles, each consisting of a Casimir-driven fall ( 2–4 ) and a conductive thermal reset ( 1.7 ). The total cycle period is approximately 7–11 , corresponding to an operating frequency of:
This is approximately one order of magnitude below the value of Hz assumed in preliminary estimates, and the array power scales proportionally. The updated power estimate is presented in Section 4.3.
4.3 Array scaling
The total harvested power for an array of units operating at frequency is:
From the oscillation frequency analysis (Section 4.2), the physically justified operating frequency is . At units:
Micro-MPD thruster concepts require a minimum input power of approximately 100 W. The architecture therefore falls approximately two orders of magnitude below this threshold:
However, continuous operation is not required. In burst mode, the capacitive storage system accumulates energy from the array over approximately 115 s, then delivers a 1-s burst at the 100 W threshold required for MPD operation. This duty cycle of approximately 0.87% is sufficient for supplementary thrust in the zero-drag interstellar environment, where each velocity increment is permanently retained. These figures represent the gross mechanical power delivered to the piezoelectric elements; the net electrical output after electromechanical conversion is presented in Section 4.6.
4.3.1 Array packing density
Each seesaw unit has a beam length of and a beam width of . The active Casimir electrode area per unit is , but the physical footprint of each unit-including beam, pivot, structural support, and inter-unit spacing-is substantially larger. For beams packed in parallel rows with a lateral pitch of (allowing clearance for mechanical oscillation), the per-unit footprint is approximately . At units, the required array area is:
This is consistent with the upper end of the aft surface diameter range shown in Figure 3 ( m diameter, corresponding to ), but exceeds the lower end ( m diameter, ). The aft surface diameter, packing density, and array count are coupled design variables; for a given spacecraft geometry, is determined by the achievable packing density rather than freely chosen. Table 1 summarizes the relationship.
FIGURE 3
TABLE 1
| Aft diameter | Available area | Max (1 pitch) | Power ( Hz) |
|---|---|---|---|
| 1 m | |||
| 3 m | |||
| 10 m |
Relationship between aft surface diameter, available array area, maximum seesaw unit count at 1 μm lateral pitch, and estimated harvested power at an operating frequency of 105 Hz.
4.4 The central energy question
The Casimir force is conservative. The energy gained from closing one gap equals the energy required to reopen it:
The see-saw couples the two sides mechanically, but does not circumvent this constraint. At the reset moment, the force holding side A at contact ( nm) exceeds the force pulling side B from maximum separation ( nm) by a factor of :
Net-positive operation therefore requires an external energy input to drive the plate separation. In this architecture, onboard waste heat provides this input via thermal expansion (Section 2.4), and the system operates as a heat engine bounded by the Carnot efficiency:
For a spacecraft with waste heat at K radiating to deep space at K:
While the theoretical Carnot limit is high due to the extreme cold of deep space, the actual conversion efficiency of the Casimir-piezoelectric chain is substantially lower, as discussed in Section 4.5.
4.5 Thermal input requirements
The thermal energy required to reset each see-saw unit via thermal expansion of an aluminum beam (/K, length μm, cross-section ) through a temperature swing of K is:
The ratio of thermal input to Casimir harvest per cycle is:
The conversion efficiency is therefore very low (). However, in the waste-heat scavenging context this ratio is acceptable because the thermal input is not generated for the purpose of driving the array-it is a byproduct of the spacecraft’s existing power systems that would otherwise be radiated into space.
At units and Hz, the required thermal input is approximately 1 W, which is well within the waste heat budget of a single RTG ( 3,750 W). At units, the required thermal input rises to approximately 1 MW, which remains within the capacity of a compact nuclear reactor.
4.6 Electrical output characterization
The preceding scaling analysis yields the gross mechanical power delivered to the piezoelectric elements. This section estimates the electrical output in terms of voltage, current, and power after piezoelectric conversion, in response to the operating requirements of MPD thrusters.
4.6.1 Material selection
We adopt PZT-5A (lead zirconate titanate) as the reference piezoelectric material due to its high electromechanical coupling coefficient () and extensive use in MEMS energy harvesting. The relevant material properties are: piezoelectric voltage coefficient , relative permittivity , and Young’s modulus .
4.6.2 Single-unit voltage
For a PZT-5A film of thickness positioned beneath the seesaw tip, the capacitance per element is:
The electrical energy per impact, accounting for the electromechanical coupling efficiency, is:
The open-circuit voltage per pulse is then:
As a cross-check, the stress-voltage method () using the peak impact stress of approximately 33 MPa (derived from the impact velocity of 0.35 m/s obtained in Section 4.2) yields , consistent with the energy method.
4.6.3 Array wiring
A single unit’s output of is far below the minimum cathode voltage required for MPD operation. However, units wired in series sum their voltages. Approximately units in series are required to reach the 40 V threshold. With total units, the array can be configured as parallel strings of series-connected units, providing ample design flexibility to match the voltage and current requirements of the thruster.
4.6.4 Total electrical power
Accounting for the piezoelectric conversion efficiency, the net electrical power is:
In burst mode, the capacitive storage system accumulates energy from the array over approximately 236 s, then delivers a 1-s burst at the 100 W threshold required for micro-MPD operation. This corresponds to a duty cycle of approximately 0.42%. In the zero-drag interstellar environment, each velocity increment is permanently retained, and the longer accumulation period does not diminish the cumulative propulsive effect over mission timescales of years to decades.
The piezoelectric film thickness is a design variable that trades voltage per pulse against capacitance: thinner films produce lower voltage but higher capacitance (and vice versa), leaving the energy per pulse unchanged. Table 2 summarizes this tradeoff.
TABLE 2
| (nm) | (fF) | (mV) | for 40 V |
|---|---|---|---|
| 10 | 15.1 | 16.8 | 2,383 |
| 20 | 7.5 | 23.8 | 1,685 |
| 50 | 3.0 | 37.5 | 1,066 |
| 100 | 1.5 | 53.1 | 754 |
| 200 | 0.75 | 75.1 | 533 |
Piezoelectric film thickness tradeoff showing capacitance per element, open-circuit voltage per impact, and number of series-connected units required to reach the 40 V MPD cathode voltage threshold.
5 Mission context
5.1 Interstellar application
This architecture is designed for interstellar space propulsion, where conventional energy sources (solar) are unavailable due to distance from any star. The Casimir effect operates independent of external radiation or stellar proximity, making it a candidate mechanism for deep-space energy harvesting. The MPD thruster’s high specific impulse is well-matched to the low-thrust, long-duration burn profiles characteristic of interstellar trajectory design.
Since the energy input is derived from waste heat that the spacecraft’s RTG produces continuously throughout its operational lifetime, the architecture provides supplementary thrust for as long as the reactor operates, which could potentially be decades for RTGs (plutonium-238 half-life: 87.7 years) or longer for nuclear reactors. The thrust duration is ultimately limited by MPD propellant supply rather than by the energy source.
The RTG’s thermal output decays gradually rather than ceasing abruptly: at 87.7 years (one half-life of plutonium-238), the RTG still produces approximately 50% of its initial waste heat and continues producing usable thermal output well beyond this point. The CPD array’s power output scales proportionally with the available waste heat, resulting in a gradual reduction in supplementary thrust over the mission lifetime rather than a sudden loss of capability.
A representative interstellar mission profile would proceed in phases: an initial boost phase using the primary propulsion system, followed by planetary gravity assists to maximize heliocentric velocity, then a sustained cruise through the heliosphere where the CPD-powered MPD thruster provides supplementary thrust to overcome residual solar gravitational deceleration. Beyond the heliopause (approximately 120 AU) and into the Oort Cloud region (>2,000 AU), the spacecraft enters a true zero-drag interstellar coast where each CPD-generated velocity increment is permanently retained. In this regime, the RTG-powered CPD system could sustain supplementary thrust for decades, with the cumulative velocity gain limited only by propellant supply rather than energy availability.
5.2 Solar system variant
For solar-system missions, an alternative variant of this architecture could employ thermal gradients (from solar radiation or onboard radioisotope sources) as an additional or primary energy input to drive the Casimir gap oscillation via temperature-dependent force modulation. Related work on thermal-expansion-driven piezoelectric harvesting from waste heat has been explored in hybrid pyroelectric-piezoelectric systems (), though without the Casimir effect or propulsion application. This variant benefits from the availability of external thermal energy but is not suitable for interstellar distances. In principle, the two variants are not mutually exclusive: a CPD array could operate on combined solar and onboard waste heat inputs during solar system transit, transitioning seamlessly to waste-heat-only operation as stellar proximity decreases. A thermal-driven variant and hybrid operational modes may be explored in future work.
6 Limitations and open questions
Net-energy source. The Casimir force is conservative: the energy gained from closing one gap equals the energy required to reopen it. The see-saw geometry does not overcome this constraint. Net-positive operation requires an external energy input. This architecture identifies onboard waste heat as that input, operating as a heat engine bounded by Carnot efficiency. The system’s value proposition rests on scavenging energy that would otherwise be radiated into space, not on extracting net energy from the Casimir force itself.
Conversion efficiency. The ratio of harvested electrical energy to thermal energy input is very low (approximately ). While this is acceptable in a waste-heat scavenging context where the input is effectively free, it means very large thermal inputs are needed at high array scales. At units, the thermal input requirement (approximately 10 MW) exceeds RTG capacity and necessitates a nuclear reactor.
Nanoscale piezoelectric response. Piezoelectric conversion efficiency under Casimir-scale impact forces ( for PZT-5A) reduces the gross mechanical output by approximately half (Section 4.6). Performance at the specific impact conditions of the seesaw (impact velocity , contact area ) requires experimental validation.
Fabrication and miniaturization. Realizing nanoscale see-saw mechanisms with the required precision, pivot quality, and Casimir-active surfaces presents substantial engineering challenges.
Scaling. Achieving propulsion-relevant power from an array of units requires to be very large. The practical limits of array density, thermal management, and mass overhead must be assessed. The array packing density analysis (Section 4.3; Table 1) establishes the relationship between aft surface area and achievable array count.
MPD system integration. Propellant ionization, magnetic field generation, propellant storage, and power conditioning electronics add mass and power overhead not yet accounted for in the energy balance. The MPD thruster is a separate downstream subsystem receiving electrical power from the capacitive storage bank (Section 2.5).
Stiction and pull-in. At nanoscale separations, Casimir and van der Waals forces can cause permanent adhesion (stiction) of the plates. Mitigation strategies from the NEMS literature-including anti-stiction coatings, textured contact surfaces, and material hardness selection-are discussed in Section 2.2. The thermal expansion reset force () exceeds the Casimir contact force () by a factor of , providing margin for adhesion recovery.
7 Conclusion and future work
We have proposed a Casimir-driven piezoelectric harvesting architecture for MPD propulsion, targeting interstellar space missions. The see-saw mechanism addresses the fundamental challenge of producing continuous piezoelectric current from the Casimir effect by creating a repeatable impact cycle. Temperature serves as a control variable to regulate oscillation characteristics.
Analysis of the see-saw energy balance demonstrates that the Casimir force alone cannot provide net energy extraction due to its conservative nature. The architecture addresses this by operating as a waste-heat scavenging system: onboard waste heat from the spacecraft’s RTG drives plate separation via thermal expansion, while the Casimir force provides the closing mechanism that generates piezoelectric impacts. The system provides continuous supplementary MPD thrust for the operational lifetime of the onboard reactor without drawing from the primary power budget, limited only by propellant supply.
Future work includes: quantitative energy-balance analysis of the see-saw cycle; experimental characterization of piezoelectric response to Casimir-scale impact forces; numerical simulation of MPD thrust output as a function of harvested power; investigation of stiction mitigation strategies; exploration of a thermal-gradient-driven variant for solar-system missions; and assessment of array scaling limits.
Statements
Data availability statement
The original contributions presented in the study are included in the article/supplementary material, further inquiries can be directed to the corresponding author.
Author contributions
NN: Conceptualization, Formal Analysis, Investigation, Methodology, Visualization, Writing – original draft. PS: Conceptualization, Supervision, Writing – review and editing.
Funding
The author(s) declared that financial support was not received for this work and/or its publication.
Conflict of interest
The author(s) declared that this work was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest.
Generative AI statement
The author(s) declared that generative AI was used in the creation of this manuscript. Claude (Anthropic, Claude Opus 4.6) was used for minor editorial revisions to the manuscript text.
Any alternative text (alt text) provided alongside figures in this article has been generated by Frontiers with the support of artificial intelligence and reasonable efforts have been made to ensure accuracy, including review by the authors wherever possible. If you identify any issues, please contact us.
Publisher’s note
All claims expressed in this article are solely those of the authors and do not necessarily represent those of their affiliated organizations, or those of the publisher, the editors and the reviewers. Any product that may be evaluated in this article, or claim that may be made by its manufacturer, is not guaranteed or endorsed by the publisher.
References
1
CasimirH. B. G. (1948). On the attraction between two perfectly conducting plates. Proc. R. Netherlands Acad. Arts Sci.51, 793–795.
2
ChoueiriE. Y. (1998). The scaling of thrust in self-field MPD thrusters. J. Propuls. Power14 (5), 744–753. 10.2514/2.5337
3
ForwardR. L. (1984). Extracting electrical energy from the vacuum by cohesion of charged foliated conductors. Phys. Rev. B. 30 (4), 1700–1702. 10.1103/PhysRevB.30.1700
4
GaurA.SaurabhN.PatelS. (2024). Exploiting the potential of pyroelectric-piezoelectric hybrid devices for low-grade thermal energy harvesting. Energy Technol.12 (1), 2300893. 10.1002/ente.202300893
5
LiW.LiX.XiaoX.ManshaiiF.LuoX.ChenG.et al (2025). A multimodal sensory textile using programmable ferroelectric nanocomposites. Adv. Mater.37 (43), e07169. 10.1002/adma.202507169
6
LifshitzE. M. (1956). The theory of molecular attractive forces between solids. Sov. Phys. JETP2, 73–83.
7
LudwigT. (2012). Quantum field energy sensor based on the casimir effect. Phys. Procedia38, 54–65. 10.1016/j.phpro.2012.08.011
8
MaclayG. J. (2009). “Thrusting against the quantum vacuum.” in Frontiers of Propulsion Science. Editor MillisM.DavisE. (AIAA: Reston, VA) Chap. 12, 227, 611–624.
9
Molina-CabreraP.HerdrichG.LauM.FausolasS.GabrielliR. A.MakerD. (2019). Pulsed Plasma Thrusters: A Worldwide Review and Long-Yearned Classification.
10
PolkJ. (2026). Lithium-Fed Magnetoplasmadynamic Thruster Testing at 120 Kw. Pasadena, CA: NASA Jet Propulsion Laboratory.
11
RU2499350C1 (2012). Piezoelectric DC Generator Based on the Casimir Effect.
12
SpanjersG. G.BromaghimD. R.LakeJ. P.DulliganM.WhiteD.SchillingJ. H.et al (2002). AFRL Microppt Development for Small Spacecraft Propulsion.
13
SuY.LiW.ChengX.ZhouY.YangS.ZhangX.et al (2022). High-performance piezoelectric composites via β phase programming. Nat. Commun.13, 4867. 10.1038/s41467-022-32518-3
14
US20190207537A1 (2019). Piezoelectric Zero-point Power Units.
15
US20200321514A1 (2020). Green Energy Harvesting Combining Piezoelectric and Casimir Force.
Summary
Keywords
casimir effect, electric propulsion, interstellar propulsion, magnetoplasmadynamic propulsion, nanoscale energy harvesting, piezoelectric energy harvesting, space propulsion, waste heat recovery
Citation
Nagalkar NR and Shukla P (2026) A casimir piezoelectric drive (CPD) architecture for supplementary MPD propulsion: a concept study. Front. Space Technol. 7:1975023. doi: 10.3389/frspt.2026.1975023
Received
21 August 2026
Revised
20 September 2026
Accepted
30 September 2026
Published
13 October 2026
Volume
7 - 2026
Edited by
Guglielmo S Aglietti, The University of Auckland, New Zealand
Reviewed by
Yuanjie Su, University of Electronic Science and Technology of China, China
Jinxing Zheng, Hefei Institutes of Physical Science, Chinese Academy of Sciences (CAS), China
Updates
Copyright
© 2026 Nagalkar and Shukla.
This is an open-access article distributed under the terms of the Creative Commons Attribution License (CC BY). The use, distribution or reproduction in other forums is permitted, provided the original author(s) and the copyright owner(s) are credited and that the original publication in this journal is cited, in accordance with accepted academic practice. No use, distribution or reproduction is permitted which does not comply with these terms.
*Correspondence: Neil R. Nagalkar, neil.nagalkar@outlook.com
Disclaimer
All claims expressed in this article are solely those of the authors and do not necessarily represent those of their affiliated organizations, or those of the publisher, the editors and the reviewers. Any product that may be evaluated in this article or claim that may be made by its manufacturer is not guaranteed or endorsed by the publisher.