Frontiers in Mechanical Engineering

Original Research

Published on 16 Dec 2025

The influence of diesel pilot injection timing on the combustion and emission characteristics of a natural gas-diesel dual-fuel engine

Yue Wu
Tao Qiu

Frontiers in Mechanical Engineering

doi 10.3389/fmech.2025.1736852

130 views

Original Research

Published on 16 Dec 2025

Research on harmonic optimization and suppression of distributed photovoltaic storage and distribution networks by improving PSO

Honglan Pei
Guangying Yan
Yingxin Zhao
Wenqiang Zhang
Chun Xiao

Frontiers in Mechanical Engineering

doi 10.3389/fmech.2025.1667908

109 views

Original Research

Accepted on 15 Dec 2025

Motor Automation Speed Regulation Method with Sliding Mode Control and Adaptive Gain

Yu Zhang
Yuping Li

Frontiers in Mechanical Engineering

Original Research

Accepted on 15 Dec 2025

Guided Wave based Health Monitoring of Composite Wind Turbine Blades: Multi-Level Damage Assessment

Anjaly J Pillai
Shirsendu Sikdar

Frontiers in Mechanical Engineering

Original Research

Accepted on 15 Dec 2025

Microstructure of Horizontally Continuously Cast Stellite Rods

Anže Bajželj
Jaka Burja

Frontiers in Mechanical Engineering

Original Research

Accepted on 15 Dec 2025

A Cable Tension Measurement Method for Transmission Lines Based on Micro-Vibration Broadband Phase Motion Magnification and Deep Learning

Zhi Ming Huang
Shuo Wang
Hongbing Wen
Zixin Li

Frontiers in Mechanical Engineering

Original Research

Published on 12 Dec 2025

Power parameter allocation of electric vehicles by integrating optimized AFSA and system parameter classification

Yang Liu
Zhijun Guo
Huijun Yao

Frontiers in Mechanical Engineering

doi 10.3389/fmech.2025.1702693

266 views

Original Research

Accepted on 10 Dec 2025

Simulation-Based Parameter Optimization and Experimental Assessment of Single-and Multi-Dimple Textures in Full-Film Lubrication

Raphael Scharf
Michael Pusterhofer
Florian Grün
Paul Staudinger

Frontiers in Mechanical Engineering

118 views

Review

Published on 10 Dec 2025

MEMS sensors and biomechanical integration for the dynamic control of prosthetic hands: a scoping review

Giuliana Baiamonte
Zeina Elrawashdeh
Salvatore Marrone
Michele Calì

Frontiers in Mechanical Engineering

doi 10.3389/fmech.2025.1736935

371 views

Correction

Published on 10 Dec 2025

Correction: Designing an E-smart manufacturing readiness assessment tool for small and medium automotive businesses

Frontiers Production Office

Frontiers in Mechanical Engineering

doi 10.3389/fmech.2025.1731677

357 views

Original Research

Published on 10 Dec 2025

Investigating the impact of imperfections around a wellbore on liner deformation during hydraulic fracturing

Yanhui Han
Dung Phan
Younane Abousleiman
Khalid Ruwaili

Frontiers in Mechanical Engineering

doi 10.3389/fmech.2025.1697890

371 views

Original Research

Accepted on 09 Dec 2025

Research on Fault Diagnosis in the Operation Monitoring of Permanent Magnet Synchronous Motors Through Deep Learning

Zhidong Guo
Xiaobei Pan

Frontiers in Mechanical Engineering

102 views

Original Research

Published on 09 Dec 2025

Automatic detection system for aircraft engine turbine blade faults based on improved PSO

Jinqiu Shang

Frontiers in Mechanical Engineering

doi 10.3389/fmech.2025.1707105

687 views

Original Research

Published on 09 Dec 2025

Mechanical and material heterogeneity, strain localization and deformation rate effects in crushable expanded polystyrene foams

Francis Yao
Meet Joshi
Megan Bland-Rothgeb
Peter Cripton
Duane Cronin
John Magliaro

Frontiers in Mechanical Engineering

doi 10.3389/fmech.2025.1718011

418 views

Original Research

Accepted on 08 Dec 2025

Design of Constant Force Polishing Device for Castings Based on Kinematic Analysis

Feifei Zhao

Frontiers in Mechanical Engineering

Original Research

Published on 08 Dec 2025

An information processing theory framework for intelligent fault diagnosis and predictive maintenance

D. Divya
O. N. Arunkumar

Frontiers in Mechanical Engineering

doi 10.3389/fmech.2025.1724801

327 views

Original Research

Accepted on 05 Dec 2025

Fluid Flow and Mass Transport along a Microchannel with Physics-Informed Neural Networks

Mehmet Melih Tatlisoz
Cetin Canpolat

Frontiers in Mechanical Engineering

164 views

Original Research

Accepted on 04 Dec 2025

Mechanical Processing Production Management Technology Based on Event Scheduling and Digital Management System

Tianshu Huo

Frontiers in Mechanical Engineering

121 views

Original Research

Accepted on 04 Dec 2025

Enhancing Risk-Based Engineering Design: A Hybrid Fuzzy Failure Analysis with Empirical Validation

Ali Aghazadeh Ardebili
Alieh Sadeghpour Roshany
Mahdad Pourmadadkar
Mostafa Ghodsi
Elio Padoano
Marco Boscolo

Frontiers in Mechanical Engineering

110 views

Original Research

Accepted on 04 Dec 2025

Multi-objective Optimization of a Multiphase Pump Booster Unit for Enhanced Hydraulic Performance

Pingyang Dong
Guangtai Shi
Yexiang Xiao
Haigang Wen
Wenjuan Lv
Xiaodong Peng

Frontiers in Mechanical Engineering

Original Research

Published on 04 Dec 2025

Inertially-enhanced damping energy sink for synergistic vibration-lightweight optimization in half-car suspensions

Yuanyuan Zhang
Ronglin Yan
Weifeng Yang

Frontiers in Mechanical Engineering

doi 10.3389/fmech.2025.1729318

401 views

Original Research

Published on 03 Dec 2025

Numerical investigation of Pelton bucket geometries for performance improvement

Hiren Shah
Gaurangkumar Chaudhari
Vijay Dhiman
Ravi Bhatt
Sachin Salunkhe
Lenka Cepova

Frontiers in Mechanical Engineering

doi 10.3389/fmech.2025.1711624

605 views

Original Research

Published on 03 Dec 2025

HAVEN: a hazard avoidance and VEhicular navigation system for autonomous maneuvering in the AREE venus rover

Arvind Mukundan
Bhardwaj Shastri
Riya Karmakar
Pratham Chandraskhar Gade
Hsiang-Chen Wang

Frontiers in Mechanical Engineering

doi 10.3389/fmech.2025.1707818

422 views

Original Research

Published on 03 Dec 2025

Improved design of passive wireless sensor for ultra-high temperature environment and its back-end circuit measurement system

Deming Li

Frontiers in Mechanical Engineering

doi 10.3389/fmech.2025.1708131

373 views

897 Publications

volumes

Volume 11 - 2025

The influence of diesel pilot injection timing on the combustion and emission characteristics of a natural gas-diesel dual-fuel engine

Research on harmonic optimization and suppression of distributed photovoltaic storage and distribution networks by improving PSO

Motor Automation Speed Regulation Method with Sliding Mode Control and Adaptive Gain

Guided Wave based Health Monitoring of Composite Wind Turbine Blades: Multi-Level Damage Assessment

Microstructure of Horizontally Continuously Cast Stellite Rods

A Cable Tension Measurement Method for Transmission Lines Based on Micro-Vibration Broadband Phase Motion Magnification and Deep Learning

Power parameter allocation of electric vehicles by integrating optimized AFSA and system parameter classification

Simulation-Based Parameter Optimization and Experimental Assessment of Single-and Multi-Dimple Textures in Full-Film Lubrication

MEMS sensors and biomechanical integration for the dynamic control of prosthetic hands: a scoping review

Correction: Designing an E-smart manufacturing readiness assessment tool for small and medium automotive businesses

Investigating the impact of imperfections around a wellbore on liner deformation during hydraulic fracturing

Research on Fault Diagnosis in the Operation Monitoring of Permanent Magnet Synchronous Motors Through Deep Learning

Automatic detection system for aircraft engine turbine blade faults based on improved PSO

Mechanical and material heterogeneity, strain localization and deformation rate effects in crushable expanded polystyrene foams

Design of Constant Force Polishing Device for Castings Based on Kinematic Analysis

An information processing theory framework for intelligent fault diagnosis and predictive maintenance

Fluid Flow and Mass Transport along a Microchannel with Physics-Informed Neural Networks

Mechanical Processing Production Management Technology Based on Event Scheduling and Digital Management System

Enhancing Risk-Based Engineering Design: A Hybrid Fuzzy Failure Analysis with Empirical Validation

Multi-objective Optimization of a Multiphase Pump Booster Unit for Enhanced Hydraulic Performance

Inertially-enhanced damping energy sink for synergistic vibration-lightweight optimization in half-car suspensions

Numerical investigation of Pelton bucket geometries for performance improvement

HAVEN: a hazard avoidance and VEhicular navigation system for autonomous maneuvering in the AREE venus rover

Improved design of passive wireless sensor for ultra-high temperature environment and its back-end circuit measurement system