Abstract
The lithium-sulfur (Li-S) battery has received a lot of attention because it is characterized by high theoretical energy density (2,600 Wh/kg) and low cost. Though many works on the “shuttle effect” of polysulfide have been investigated, lithium metal anode is a more challenging problem, which leads to a short life, low coulombic efficiency, and safety issues related to dendrites. As a result, the amelioration of lithium metal anode is an important means to improve the performance of lithium sulfur battery. In this paper, improvement methods on lithium metal anode for lithium sulfur batteries, including adding electrolyte additives, using solid, and/or gel polymer electrolyte, modifying separators, applying a protective coating, and providing host materials for lithium deposition, are mainly reviewed. In addition, some challenging problems, and further promising directions are also pointed out for future research and development of lithium metal for Li-S batteries.
Introduction
As a kind of lithium metal secondary battery, lithium-sulfur battery is very likely to be another energy storage device for its high theoretical energy density (2,600 Wh kg−1) and specific capacity (1,675 mAh g−1) (Lu et al., ; Tao T. et al., ; Li J. H. et al., ). Meanwhile, using sulfur as cathodic material makes it cheaper and more environmentally friendly (Yin et al., ). However, the shuttle effect and uneven deposition of lithium limit the practical application of lithium-sulfur batteries (Li et al., ; Manthiram et al., ). Other problems such as poor electrical conductivity and severe volume change of sulfur also limit the performance of batteries to a certain extent (Evers and Nazar, ). At present, the improvement of lithium sulfur battery mainly focuses on the cathode, while much less research has been done on lithium metal anodes.
In Li-S batteries, the metallic lithium is oxidized to produce lithium ion firstly. Unfortunately, the stripping of lithium is uneven commonly, which affects the uniform deposition of lithium in the next step. The uneven and porous lithium deposition layer leads to a large change in its volume, fracturing the fragile solid electrolyte interface (SEI) and then consuming the inner fresh lithium to form a new SEI after reacting with the electrolyte. Polysulfides formed during the charging process transfer to the Li metal anode via the electrolyte, react with lithium irreversibly. At the same time, the uneven deposition of lithium leads to the enrichment of lithium ions in the tip region, and aggravating the growth of lithium dendrites. When the dendrite grows to a certain extent, the electrical contact with the substrate will be broken to produce the unreactive “dead” lithium, which increases the internal resistance and attenuates the capacity of the battery. To make matters worse, dendrites can even pierce through separator, posing a safety hazard. These challenges lead to the drawbacks of Li-S batteries.
So, the improvement of lithium metal anode could be classified into two aspects: protecting active lithium from side reactions and guiding uniform deposition of lithium. Since gain/loss of one electron especially that in 2s orbit should be very fast, the solutions to Li metal are not fully addressed, and there are few reviews on Li metal anode (Cheng et al., ; Yan et al., ). As a result, here we summarized some promising methods: (1) Adding additives to the electrolyte. (2) Using solid electrolytes or gel polymer electrolytes (Marom et al., ). (3) Modifying the separators. (4) Coating protective layers on the surface of lithium directly. (5) Providing host materials for lithium deposition. We summarized the above five directions in the recent 5 years; challenges and further directions are also pointed out.
Adding Additives to the Electrolyte
Organic liquid electrolyte, especially ether-based electrolyte, is commonly used in lithium-sulfur batteries for its high ionic conductivity, good interface contact with electrodes, and less side reaction with lithium. However, issues originating from the dissolution of intermediate polysulfides make it necessary to add suitable additives to protect the lithium metal anode. So far, the additives include nitrates, iodides, sulfur-containing compounds, and various organic compounds, and their functions are listed in Table S1.
It is well-known that LiNO3 has the ability to protect the lithium metal anode effectively by participating in forming a robust SEI layer in situ on the metal surface (Liang et al., ). The composition of SEI was investigated by Operando X-ray absorption spectroscopy (XAS); results showed that during the initial discharge process, LiNO3 reacted with polysulfides to form Li2SO4, Li2SO3, and LiNO2, which composed a stable SEI on the surface of anode to hamper the side reactions between polysulfides and lithium (Zhang et al., ). Other types of nitrates such as La(NO3)3 and KNO3 were also studied in particular. Both the cation and nitrate can participate in improving the stability of SEI on anode (Figure 1A) (Liu S. et al., ), and a Li-S full battery using 1 M LiTFSI (DME:DOL = 1:1 v:v) electrolyte added with 0.1 M KNO3 exhibited an average discharging capacity of 687 mAh/g within 100 cycles, which was higher than the one with 0.1 M LiNO3 (average 637 mAh/g) (Jia et al., ).
Figure 1
Iodide, such as LiI and InI3, had also acquired outstanding breakthrough (Eo et al., ; Liu et al., ). Quantum chemistry calculations showed that the I· radicals reacted with DME to form comb-branched polyether in solution (Figure 1B), which suppress the dissolution of polysulfides and then protect the Li metal anode simultaneously (Wu et al., ). Poly(sulfur-random-triallylamine) (PST) (Figure 1C) (Li G. et al., ), SOCl2 (Li S. et al., ), 1,1,2,2-tetrafluoroethyl-2,2,3,3-tetrafluoropropyl ether (TTE) (Qian et al., ), and magnesium oxide nanoparticles (Ponraj et al., ) were also proven to be effectual.
In order to reduce the polysulfides in electrolyte during the cycling of Li-S battery, additives such as dithiothreitol (DTT), which can slice the S–S bond to accelerate the conversion from polysulfides to Li2S2/LiS2 (Liu M. et al., ), biphenyl-4,4′-dithiol (BPD) (Wu H. L. et al., ) and carbon disulfide (CS2) (Gu et al., ), which could react with polysulfides to reduce the chance of contact with the anode, were developed.
Using Other Types of Electrolyte
Ionic liquid electrolyte is an electrolyte composed entirely of anion and cation, which determines its high safety, excellent stability, and strong solubility to lithium salt (Ghandi, ). Moreover, the weak solvation of ionic liquids can reduce the solubility of polysulfides. However, ionic liquids usually have high viscosity, which leads to low ionic conductivity. Adding an appropriate amount of solvents such as DME and DOL to achieve a balance between ionic conductivity and solubility of polysulfides is a suitable choice (Yang et al., ). For example, the room temperature ionic conductivity of N-methoxyethyl-N-methylpyrrolidinium bis (trifluoromethanesulfonyl)-imide (P1,2O1TFSI) with 30 wt.% TEGDME as the diluent was increased to 4.303 mS cm−1, the Li-S full battery using the electrolyte showed an initial discharge capacity of 1,264 and 911.4 mAh g−1 was retained after 50 cycles (Wu et al., ).
Solid electrolyte is also an important direction to improve lithium metal anode by blocking the polysulfides physically. Generally, it can be classified into inorganic solid electrolyte and polymer solid electrolyte. Inorganic solid electrolytes are mainly composed of sulfides, oxides, and phosphates. Examples of sulfides are Li6PS5Cl (Figure S1A), Li3PS4, and Li10GeP2S12 (Yamada et al., ; Han et al., ; Yao et al., ). Oxides include Li3.3La0.56TiO3, Li7La3Zr2O12, and Li14ZnGe4O16 (Zheng et al., ; Yu et al., ). Li1.3Al0.3Ge1.7(PO4)3, Li1.3Al0.3Ti1.7(PO4)3, and Li2P5O6N5 (Monchak et al., ; Meesala et al., ) are typical representatives of phosphates. Polymer solid electrolytes are based on polymer matrix such as PEO, PMMA, PVDF, and PAN without liquid phase. It is characterized by chemical stability, mechanical persistence (durability), and flexibility. However, the low room temperature ionic conductivity plagues the direct application of them (Lin et al., ), and methods such as doping (Monchak et al., ), blending, and cross-linking are applied to improve the performance of solid electrolyte. Among them, adding fillers may be the most effective route. Fillers such as LiN3 (Eshetu et al., ), Li7La3Zr2O12 (LLZO) (Figure S1B) (Tao X. et al., ), MoS2 (Xu et al., ), food grade starch (Lin Y. et al., ), and halloysite (Lin et al., ) were proven to be effectual. Besides, constructing multilayer solid electrolyte by coupling a dense layer that provides supporting function and hosts for electrolytes with a thin layer to block the polysulfides and inhibit the growth of dendrites (Figure S1C) (Fu et al., ) was another promising solution.
As an intermediate of liquid electrolyte and all-solid electrolyte, the gel-polymer electrolyte (GPE) therefore has relatively high ionic conductivity and the ability to inhibit polysulfide shuttle (Figure S1D) (Choi et al., ). But this GPE is not perfect since its mechanical properties are poor and the ionic conductivity still has room for improvement. The main improvement methods are adding nano-fillers, compounding with plasticizers, and so on (Figure S1E) (Cheng et al., ). Specific examples of nano-fillers include ZnO, MgO, Al2O3, polyethylene, and polystyrene (Kim, ; Wu N. et al., ; Tripathi and Kumar, ).
Modification on Separators
Coating functional layers that can block polysulfides and modify lithium metal anode on the surface of common separator is also an important way, the actions of which are summarized in Table S2. A layer of porous carbon material on the surface of the separator not only can immobilize polysulfides but also can be used as an upper current collector to improve the utilization rate of active materials. Hence, various carbon materials are used to modified the separator, such as mesoporous carbon (Balach et al., ), porous graphene (Zhai et al., ), super-P (Zhu et al., ), microporous carbon nanofiber (Figure S2A) (Chung et al., ), and acetylene black (Figure S2B) (Yang et al., ). A multifunctional separator integrated with one or more layers is also a popular improvement direction. Utilizing the synergy effect of carbon and BN on the two sides of a membrane, the performance of the Li-S battery using 1 M LiTFSI in DIOX and DME electrolyte (v:v = 1:1) had been significantly improved; there was still 702 mAh g−1 specific capacity at a rate of 4C (Figure S2C) (Kim et al., ). On the same principle, a modified separator with compounds of Ketjen Black and MnO coated on Celgard 2400 membrane was developed (Qian et al., ).
MXenes are a kind of ultrathin two-dimensional materials that have very high conductivity and surface homogeneity (Figure S2D) (Anasori et al., ). By coating Ti3C2TX (T is -O, -OH, or -F) on commercial Celgard 2400 separator, a superior composite membrane can be obtained (Figure S2E). At a rate of 0.5C, the capacity of the Li-S battery after 500 cycles was 550 mAh g−1, and the capacity attenuation per cycle was only 0.063% in an electrolyte of 1 M LiTFSI in DME and DOL (v:v = 1:1) (Song et al., ).
Coating on the Surface of Lithium
Applying a protective layer directly on the surface of the Li anode is also a facile and effective means. The main method is coating some protective layers such as carbon-based materials, polymer, alloy, and ceramic layer, whose actions are summarized in Table S3.
Without question, the protective layer should have sufficient lithium ionic conductivity, chemical inertness, and superior stability. Various carbon materials such as carbon nanofiber (CNF) (Figure S3A) (Zhang A. Y. et al., ), nitrogen-doped few-layer graphene (N-FLG) sheets (Figures S3B, S4A) (Kang et al., ), artificial graphite particles (Sun et al., ), multi-walled carbon nanotube (Deng et al., ), and ladderlike carbon nanoarrays (Figure S4B) (Liu L. et al., ) were used to homogenize the current density and promote the even deposition of lithium.
Various polymers also provide a wide range of options for surface modification because of the unique characters (Liu Z. C. et al., ). For example, Li-S battery using a lithium metal anode modified with a soft, viscous polymer layer showed excellent cycling stability (Figure S3C), with 737 mAh g−1 specific capacity after 300 cycles at 0.2C when using an electrolyte of 0.6 M LiTFSI in DOL/DME (v:v, 1/1) with 0.4 M LiNO3 as an additive (Zheng et al., ). This novel protective layer owned characteristic of slow flow, so it can homogenize the flow of lithium ions and then inhibit dendrite growth (Figure S4C); another advantage is that the process for modifying a polymer protective layer is relatively simple. A 4-μm-thick β-PVDF coating on lithium metal anode made the coulombic efficiency of Cu-Li cells remain 98% in 200 cycles at 1 mA/cm2 when using an electrolyte of 1 M LiTFSI in DOL and DME (v:v = 1:1) with 3 wt.% LiNO3 additive (Figure S4D) (Luo et al., ).
Providing Host Materials for Lithium Deposition
Layered or three-dimensional frame structure compound has been considered as an effective route to avoid the issues such as the uneven lithium deposition, severe volume change, and safety risks. The frame structure materials include carbon-based materials, polymer materials, metallic materials, and so on, and their actions are summarized in Table S4.
Reduced graphene oxide (Figure 2A and Figure S5A) (Lin et al., ) and three-dimensional non-stacked framework graphene (Figure S5B) (Zhang R. et al., ) are good illustrations of carbon-based materials. Adding lithiophilic component such as ZnO could further improve the lithiophilicity and reduce the lithium nucleation overpotential (Figure S5C) (Liang et al., ).
Figure 2
Highly cross-linked polymeric substrates have abundant pore channels where the Li+ can transport rapidly. By electrospinning technique, a polyimide (PI) mesh with a lithiophilic ZnO shell was obtained (Figure 2B), then molten metal lithium was infused into the matrix to prepare a composite Li anode (Figure S5D) (Liu Y. et al., ). Copper is well-suited as an anode current collector for its high conductivity and stability at low potential. Hence, numerous studies were focused on 3D Cu; notable examples of it are 3D Cu/Li (Figure 2C and Figure S5F) (Yang et al., ) and copper mesh /Li composite anode (Figure 2D and Figure S5E) (Li Q. et al., ).
In addition, lithium alloy is also a simple and scalable way to improve the Li-S battery. For example, a Li-Mg (mass ratio: 18.6:81.4) alloy anode was developed. The Mg matrix provided host for the lithium to acquire an even deposition. Also, Mg element participated in the formation of a robust SEI (Kong et al., ). Other types of lithium alloys such as Li/Sn (Qiu et al., ) and Li/Al (Zhong et al., ) had also been proven effective though more studies are still needed.
Summary
Due to various methods, the performance of lithium-sulfur battery has been greatly improved. However, batteries tested in the experiment are all coin cells, the relatively low current density and the excess amount of lithium underestimate the problems of lithium metal anode to some extent. It is necessary to test the electrochemical performance under the conditions of high current density (>3.0 mA/cm2) (Yan et al., ) and matching the amount of lithium with the cathodic active materials, so as to meet the needs of practical application.
In addition, problems in lithium-sulfur batteries are various and correlated. Meanwhile, superior comprehensive performance rather than single performance improvement is more urgently needed. Considering that the gel polymer electrolyte has good compatibility with the electrodes, which is favorable for the uniform deposition and stripping of lithium physically. At the same time, the migration of polysulfides can also be suppressed to some extent. More importantly, the gel polymer electrolyte is simple in manufacturing process and low in cost, which is advantageous for mass production. Therefore, we believe that gel electrolyte, which improved by adding fillers, blending, cross-linking and so on, is a very promising direction.
Lastly, the use of more advanced technology to study the mechanism of lithium metal anodes in lithium-sulfur batteries is also of great help in guiding the improvement strategies. All in all, the understanding and researches on the lithium metal anode in lithium-sulfur batteries are still less, and in order to solve the practical application of lithium-sulfur batteries, more work needs to be done.
Statements
Author contributions
All authors listed have made a substantial, direct and intellectual contribution to the work, and approved it for publication.
Funding
Open access publication fees were financed by the funding agencies. The authors gratefully acknowledge financial support from the National Materials Genome Project (2016YFB0700600), the National Natural Science Foundation Committee of China (Distinguished Youth Scientists Project of 51425301, U1601214, 21374021, 51573013, 51773092, and 51772147), the 1000 Youth Talents Plan of the National Natural Science Foundation of China (51773092), the Research Foundation of State Key Lab (ZK201805 and ZK201717), the Jiangsu Distinguished Professorship Program (2016), and the Postgraduate Research & Practice Innovation Program of Jiangsu Province (KYCX19_0832).
Conflict of interest
The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest.
Supplementary material
The Supplementary Material for this article can be found online at: https://www.frontiersin.org/articles/10.3389/fchem.2019.00827/full#supplementary-material
References
1
AnasoriB.LukatskayaM. R.GogotsiY. (2017). 2D metal carbides and nitrides (MXenes) for energy storage. Nat. Rev. Mater.2:16098. 10.1038/natrevmats.2016.98
2
BalachJ.JaumannT.KloseM.OswaldS.EckertJ.GiebelerL. (2015). Functional mesoporous carbon-coated separator for long-life, high-energy lithium-sulfur batteries. Adv. Funct. Mater.25, 5285–5291. 10.1002/adfm.201502251
3
ChengX.-B.HuangJ.-Q.ZhangQ. (2017). Review—li metal anode in working lithium-sulfur batteries. J. Electrochem. Soc.165, A6058–A6072. 10.1149/2.0111801jes
4
ChengX. L.PanJ.ZhaoY.LiaoM.PengH. S. (2018). Gel polymer electrolytes for electrochemical energy storage. Adv. Energy Mater.8:1702184. 10.1002/aenm.201702184
5
ChoiS.SongJ.WangC.ParkS.WangG. (2017). Multifunctional free-standing gel polymer electrolyte with carbon nanofiber interlayers for high-performance lithium-sulfur batteries. Chem. Asian J.12, 1470–1474. 10.1002/asia.201700402
6
ChungS. H.HanP.SinghalR.KalraV.ManthiramA. (2015). Electrochemically stable rechargeable lithium-sulfur batteries with a microporous carbon nanofiber filter for polysulfide. Adv. Energy Mater.5:1500738. 10.1002/aenm.201500738
7
DengY.LuH.CaoY.XuB.HongQ.CaiW.et al. (2019). Multi-walled carbon nanotube interlayers with controllable thicknesses for high-capacity and long-life lithium metal anodes. J. Power Sourc.412, 170–179. 10.1016/j.jpowsour.2018.11.037
8
EoS. M.ChaE.KimD. W. (2009). Effect of an inorganic additive on the cycling performances of lithium-ion polymer cells assembled with polymer-coated separators. J. Power Sour.189, 766–770. 10.1016/j.jpowsour.2008.08.008
9
EshetuG. G.JudezX.LiC.BondarchukO.Rodriguez-MartinezL. M.ZhangH.et al. (2017). Lithium azide as an electrolyte additive for all-solid-state lithium-sulfur batteries. Angew. Chem. Int. Ed. Engl.56, 15368–15372. 10.1002/anie.201709305
10
EversS.NazarL. F. (2013). New approaches for high energy density lithium-sulfur battery cathodes. Acc. Chem. Res.46, 1135–1143. 10.1021/ar3001348
11
FuK.GongY.HitzG. T.McOwenD. W.LiY.XuS.et al. (2017). Three-dimensional bilayer garnet solid electrolyte based high energy density lithium metal–sulfur batteries. Energy Environ. Sci.10, 1568–1575. 10.1039/C7EE01004D
12
GhandiK. (2014). A review of ionic liquids, their limits and applications. Green Sustain. Chem.4, 44–53. 10.4236/gsc.2014.41008
13
GuS.WenZ.QianR.JinJ.WangQ.WuM.et al. (2016). Carbon disulfide cosolvent electrolytes for high-performance lithium sulfur batteries. ACS Appl. Mater. Interfaces8, 34379–34386. 10.1021/acsami.6b11619
14
HanF.YueJ.FanX. L.GaoT.LuoC.MaZ.et al. (2016). High-performance all-solid-state lithium-sulfur battery enabled by a mixed-conductive Li2S nanocomposite. Nano Lett.16, 4521–4527. 10.1021/acs.nanolett.6b01754
15
JiaW.FanC.WangL.WangQ.ZhaoM.ZhouA.et al. (2016). Extremely Accessible Potassium Nitrate (KNO3) as the highly efficient electrolyte additive in lithium battery. Acs Appl. Mater. Interfaces8, 15399–15405. 10.1021/acsami.6b03897
16
KangH. K.WooS. G.KimJ. H.YuJ. S.LeeS. R.KimY. J. (2016). Few-layer graphene island seeding for dendrite-free Li metal electrodes. ACS Appl. Mater. Interfaces8:26895–26901. 10.1021/acsami.6b09757
17
KimJ. K. (2017). Hybrid gel polymer electrolyte for high-safety lithium-sulfur batteries. Mater. Lett.187, 40–43. 10.1016/j.matlet.2016.10.069
18
KimP. J. H.SeoJ.FuK.ChoiJ.LiuZ. M.KwonJ.et al. (2017). Synergistic protective effect of a BN-carbon separator for highly stable lithium sulfur batteries. Npg Asia Mater.9:e375–e375. 10.1038/am.2017.51
19
KongL. L.WangL.NiZ. C.LiuS.LiG. R.GaoX. P. (2019). Lithium–magnesium alloy as a stable anode for lithium–sulfur battery. Adv. Funct. Mater.29:1808756. 10.1002/adfm.201808756
20
LiG.GaoY.HeX.HuangQ.ChenS.KimS. H.et al. (2017). Organosulfide-plasticized solid-electrolyte interphase layer enables stable lithium metal anodes for long-cycle lithium-sulfur batteries. Nat. Commun.8:850. 10.1038/s41467-017-00974-x
21
LiJ. H.LiuZ. C.ZhangQ. B.ChengY.ZhaoB. T.DaiS. G.et al. (2019). Anion and cation substitution in transition-metal oxides nanosheets for high-performance hybrid supercapacitors. Nano Energy57, 22–33. 10.1016/j.nanoen.2018.12.011
22
LiQ.ZhuS. P.LuY. Y. (2017). 3D porous Cu current collector/Li-Metal composite anode for stable lithium-metal batteries. Adv. Funct. Mater.27:1606422. 10.1002/adfm.201606422
23
LiS.DaiH.LiY.LaiC.WangJ.HuoF.et al. (2019). Designing Li-protective layer via SOCl2 additive for stabilizing lithium-sulfur battery. Energy Storage Mater.18, 222–228. 10.1016/j.ensm.2018.09.012
24
LiZ.HuangJ.LiawB. Y.MetzlerV.ZhangJ. B. (2014). A review of lithium deposition in lithium-ion and lithium metal secondary batteries. J. Power Sour.254, 168–182. 10.1016/j.jpowsour.2013.12.099
25
LiangX.WenZ. Y.LiuY.WuM. F.JinJ.ZhangH.et al. (2011). Improved cycling performances of lithium sulfur batteries with LiNO3-modified electrolyte. J. Power Sour.196, 9839–9843. 10.1016/j.jpowsour.2011.08.027
26
LiangZ.LinD.ZhaoJ.LuZ.LiuY.LiuC.et al. (2016). Composite lithium metal anode by melt infusion of lithium into a 3D conducting scaffold with lithiophilic coating. Proc. Natl. Acad. Sci. U.S.A.113, 2862–2867. 10.1073/pnas.1518188113
27
LinD.LiuW.LiuY.LeeH. R.HsuP. C.LiuK.et al. (2016a). High ionic conductivity of composite solid polymer electrolyte via in situ synthesis of monodispersed SiO2 nanospheres in Poly(ethylene oxide). Nano Lett.16, 459–465. 10.1021/acs.nanolett.5b04117
28
LinD.LiuY.LiangZ.LeeH. W.SunJ.WangH.et al. (2016b). Layered reduced graphene oxide with nanoscale interlayer gaps as a stable host for lithium metal anodes. Nat. Nanotechnol.11, 626–632. 10.1038/nnano.2016.32
29
LinY.LiJ.LiuK.LiuY. X.LiuJ.WangX. M. (2016). Unique starch polymer electrolyte for high capacity all-solid-state lithium sulfur battery. Green Chem.18, 3796–3803. 10.1039/C6GC00444J
30
LinY.WangX. M.LiuJ.MillerJ. D. (2017). Natural halloysite nano-clay electrolyte for advanced all-solid-state lithium-sulfur batteries. Nano Energy31, 478–485. 10.1016/j.nanoen.2016.11.045
31
LiuL.YinY. X.LiJ. Y.GuoY. G.WanL. J. (2018). Ladderlike carbon nanoarrays on 3D conducting skeletons enable uniform lithium nucleation for stable lithium metal anodes. Chem. Commun.54, 5330–5333. 10.1039/C8CC02672F
32
LiuM.ChenX.ChenC.MaT.HuangT.YuA. (2019). Dithiothreitol as a promising electrolyte additive to suppress the “shuttle effect” by slicing the disulfide bonds of polysulfides in lithium-sulfur batteries. J. Power Sour.424, 254–260. 10.1016/j.jpowsour.2019.03.113
33
LiuM.RenY. X.JiangH. R.LuoC.KangF. Y.ZhaoT. S. (2017). An efficient Li2S-based lithium-ion sulfur battery realized by a bifunctional electrolyte additive. Nano Energy40, 240–247. 10.1016/j.nanoen.2017.08.017
34
LiuS.LiG. R.GaoX. P. (2016). Lanthanum nitrate as electrolyte additive to stabilize the surface morphology of lithium anode for lithium-sulfur battery. ACS Appl. Mater. Interfaces8, 7783–7789. 10.1021/acsami.5b12231
35
LiuY.LinD.LiangZ.ZhaoJ.YanK.CuiY. (2016). Lithium-coated polymeric matrix as a minimum volume-change and dendrite-free lithium metal anode. Nat. Commun.7:10992. 10.1038/ncomms10992
36
LiuZ. C.YuanX. H.ZhangS. S.WangJ.HuangQ. H.YuN. F.et al. (2019). Three-dimensional ordered porous electrode materials for electrochemical energy storage. Npg Asia Mater.11:12. 10.1038/s41427-019-0112-3
37
LuL. G.HanX. B.LiJ. Q.HuaJ. F.OuyangM. G. (2013). A review on the key issues for lithium-ion battery management in electric vehicles. J. Power Sources226, 272–288. 10.1016/j.jpowsour.2012.10.060
38
LuoJ.FangC.-C.WuN.-L. (2018). High polarity poly(vinylidene difluoride) thin coating for dendrite-free and high-performance lithium metal anodes. Adv. Energy Mater.8, 1701482-1–1701482-7. 10.1002/aenm.201701482
39
ManthiramA.FuY.ChungS. H.ZuC.SuY. S. (2014). Rechargeable lithium-sulfur batteries. Chem. Rev.114, 11751–11787. 10.1021/cr500062v
40
MaromR.AmalrajS. F.LeiferN.JacobD.AurbachD. (2011). A review of advanced and practical lithium battery materials. J. Mater. Chem.21, 9938–9954. 10.1039/c0jm04225k
41
MeesalaY.JenaA.ChangH.LiuR. S. (2017). Recent advancements in Li-ion conductors for all-solid-state li-ion batteries. Acs Energy Lett.2, 2734–2751. 10.1021/acsenergylett.7b00849
42
MonchakM.HupferT.SenyshynA.BoysenH.ChernyshovD.HansenT.et al. (2016). Lithium diffusion pathway in Li(1.3)Al(0.3)Ti(1.7)(PO4)3 (LATP) superionic conductor. Inorg. Chem.55, 2941–2945. 10.1021/acs.inorgchem.5b02821
43
PonrajR.KannanA. G.AhnJ. H.KimD. W. (2016). Improvement of cycling performance of lithium-sulfur batteries by using magnesium oxide as a functional additive for trapping lithium polysulfide. ACS Appl. Mater. Interfaces8, 4000–4006. 10.1021/acsami.5b11327
44
QianF.ShaoJ.ChenY.ZhuG.QuQ.ZhengH. (2018). Partially fluorinated ether as an electrolyte additive to modify electrode surface and suppress dissolution of polysulfides in Li-S batteries. Electrochem. Energy Technol.4, 39–46. 10.1515/eetech-2018-0005
45
QianX. Y.JinL.ZhaoD.YangX. L.WangS. W.ShenX. Q.et al. (2016). Ketjen black-MnO composite coated separator for high performance rechargeable lithium-sulfur battery. Electrochim. Acta192, 346–356. 10.1016/j.electacta.2016.01.225
46
QiuH.TangT.AsifM.LiW.ZhangT.HouY. (2019). Stable lithium metal anode enabled by lithium metal partial alloying. Nano Energy65:103989. 10.1016/j.nanoen.2019.103989
47
SongJ.SuD.XieX.GuoX.BaoW.ShaoG.et al. (2016). Immobilizing polysulfides with MXene-functionalized separators for stable lithium-sulfur batteries. ACS Appl. Mater. Interfaces8, 29427–29433. 10.1021/acsami.6b09027
48
SunY. M.ZhengG. Y.SehZ. W.LiuN.WangS.SunJ.et al. (2016). Graphite-encapsulated Li-metal hybrid anodes for high-capacity Li batteries. Chem1, 287–297. 10.1016/j.chempr.2016.07.009
49
TaoT.LuS.FanY.LeiW.HuangS.ChenY. (2017). Anode improvement in rechargeable lithium-sulfur batteries. Adv. Mater.29:1700542. 10.1002/adma.201700542
50
TaoX.LiuY.LiuW.ZhouG.ZhaoJ.LinD.et al. (2017). Solid-state Lithium–sulfur batteries operated at 37°C with composites of nanostructured Li7La3Zr2O12/Carbon foam and polymer. Nano Lett.17, 2967–2972. 10.1021/acs.nanolett.7b00221
51
TripathiM.KumarA. (2018). Zinc oxide nanofiller-based composite polymer gel electrolyte for application in EDLCs. Ionics24, 3155–3165. 10.1007/s11581-018-2504-8
52
WuF.LeeJ. T.NittaN.KimH.BorodinO.YushinG. (2015a). Lithium iodide as a promising electrolyte additive for lithium-sulfur batteries: mechanisms of performance enhancement. Adv. Mater.27, 101–108. 10.1002/adma.201404194
53
WuF.ZhuQ. Z.ChenR. J.ChenN.ChenY.LiL. (2015b). A safe electrolyte with counterbalance between the ionic liquid and Tris(ethylene glycol)dimethyl ether for High Performance Lithium-Sulfur Batteries. Electrochim. Acta184, 356–363. 10.1016/j.electacta.2015.10.109
54
WuH. L.ShinM.LiuY. M.SeeK. A.GewirthA. A. (2017). Thiol-based electrolyte additives for high-performance lithium-sulfur batteries. Nano Energy32, 50–58. 10.1016/j.nanoen.2016.12.015
55
WuN.WangW.WeiY.LiT. H. (2017). Studies on the effect of nano-sized MgO in magnesium-ion conducting gel polymer electrolyte for rechargeable magnesium batteries. Energies10:1215. 10.3390/en10081215
56
XuR. C.XiaX. H.WangX. L.XiaY.TuJ. P. (2017). Tailored Li2S-P2S5 glass-ceramic electrolyte by MoS2 doping, possessing high ionic conductivity for all-solid-state lithium-sulfur batteries. J. Mater. Chem.5, 2829–2834. 10.1039/C6TA10142A
57
YamadaT.ItoS.OmodaR.WatanabeT.AiharaY.AgostiniM.et al. (2015). All solid-state lithium-sulfur battery using a glass-type P2S5-Li2S electrolyte: benefits on anode kinetics. J. Electrochem. Soc.162, A646–A651. 10.1149/2.0441504jes
58
YanC.ZhangX.-Q.HuangJ.-Q.LiuQ.ZhangQ. (2019). Lithium-Anode protection in lithium-sulfur batteries. Trends Chem.1, 693–704. 10.1016/j.trechm.2019.06.007.
59
YangC. P.YinY. X.ZhangS. F.LiN. W.GuoY. G. (2015). Accommodating lithium into 3D current collectors with a submicron skeleton towards long-life lithium metal anodes. Nat. Commun.6:8058. 10.1038/ncomms9058
60
YangD.HeL.LiuY.YanW.LiangS.ZhuY.et al. (2019). An acetylene black modified gel polymer electrolyte for high-performance lithium–sulfur batteries. J. Mater. Chem.7, 13679–13686. 10.1039/C9TA03123E
61
YangY. B.MenF.SongZ. P.ZhouY. H.ZhanH. (2017). N-methoxyethyl-N-methylpyrrolidinium bis (trifluoromethanesulfonyl) imide ionic liquid based hybrid electrolyte for lithium sulfur batteries. Electrochim. Acta256, 37–43. 10.1016/j.electacta.2017.10.020
62
YaoX. Y.HuangN.HanF. D.ZhangQ.WanH. L.MwizerwaJ. P.et al. (2017). High-performance all-solid-state lithium-sulfur batteries enabled by amorphous sulfur-coated reduced graphene oxide cathodes. Adv. Energy Mater.7:1602923. 10.1002/aenm.201602923
63
YinY. X.XinS.GuoY. G.WanL. J. (2013). Lithium-sulfur batteries: electrochemistry, materials, and prospects. Angew. Chem. Int. Ed. Engl.52, 13186–13200. 10.1002/anie.201304762
64
YuS.SchmidtR. D.Garcia-MendezR.HerbertE.DudneyN. J.WolfenstineJ. B.et al. (2015). Elastic properties of the solid electrolyte Li7La3Zr2O12 (LLZO). Chem. Mater.28, 197–206. 10.1021/acs.chemmater.5b03854
65
ZhaiP.-Y.PengH.-J.ChengX.-B.ZhuL.HuangJ.-Q.ZhuW.et al. (2017). Scaled-up fabrication of porous-graphene-modified separators for high-capacity lithium–sulfur batteries. Energy Storage Mater.7, 56–63. 10.1016/j.ensm.2016.12.004
66
ZhangA. Y.FangX.ShenC. F.LiuY. H.ZhouC. W. (2016). A carbon nanofiber network for stable lithium metal anodes with high Coulombic efficiency and long cycle life. Nano Res.9, 3428–3436. 10.1007/s12274-016-1219-2
67
ZhangL.LingM.FengJ.MaiL.LiuG.GuoJ. (2018). The synergetic interaction between LiNO3 and lithium polysulfides for suppressing shuttle effect of lithium-sulfur batteries. Energy Storage Mater.11, 24–29. 10.1016/j.ensm.2017.09.001
68
ZhangR.ChengX. B.ZhaoC. Z.PengH. J.ShiJ. L.HuangJ. Q.et al. (2016). Conductive nanostructured scaffolds render low local current density to inhibit lithium dendrite growth. Adv. Mater. Weinheim.28, 2155–2162. 10.1002/adma.201504117
69
ZhengG. Y.WangC.PeiA.LopezJ.ShiF. F.ChenZ.et al. (2016). High-performance lithium metal negative electrode with a soft and flowable polymer coating. Acs Energy Lett.1, 1247–1255. 10.1021/acsenergylett.6b00456
70
ZhengZ.FangH.LiuZ.WangY. (2014). A fundamental stability study for amorphous LiLaTiO3Solid electrolyte. J. Electrochem. Soc.162, A244–A248. 10.1149/2.0011503jes
71
ZhongH.SangL.DingF.SongJ. X.MaiY. H. (2018). Conformation of lithium-aluminium alloy interphase-layer on lithium metal anode used for solid state batteries. Electrochim. Acta277, 268–275. 10.1016/j.electacta.2018.04.191
72
ZhuJ. D.GeY. Q.KimD.LuY.ChenC.JiangM. J.et al. (2016). A novel separator coated by carbon for achieving exceptional high performance lithium-sulfur batteries. Nano Energy20, 176–184. 10.1016/j.nanoen.2015.12.022
Summary
Keywords
lithium-sulfur battery, anode, dendrite, safety, gel polymer electrolyte, coating
Citation
Xiong X, Yan W, You C, Zhu Y, Chen Y, Fu L, Zhang Y, Yu N and Wu Y (2019) Methods to Improve Lithium Metal Anode for Li-S Batteries. Front. Chem. 7:827. doi: 10.3389/fchem.2019.00827
Received
22 July 2019
Accepted
14 November 2019
Published
10 December 2019
Volume
7 - 2019
Edited by
Keyu Xie, Northwestern Polytechnical University, China
Reviewed by
Jin Tao Zhang, Nanyang Technological University, Singapore; Hossein Yadegari, Imperial College London, United Kingdom; Zhian Zhang, Central South University, China
Updates
Copyright
© 2019 Xiong, Yan, You, Zhu, Chen, Fu, Zhang, Yu and Wu.
This is an open-access article distributed under the terms of the Creative Commons Attribution License (CC BY). The use, distribution or reproduction in other forums is permitted, provided the original author(s) and the copyright owner(s) are credited and that the original publication in this journal is cited, in accordance with accepted academic practice. No use, distribution or reproduction is permitted which does not comply with these terms.
*Correspondence: Nengfei Yu yunf@njtech.edu.cnYuping Wu wuyp@fudan.edu.cn
This article was submitted to Electrochemistry, a section of the journal Frontiers in Chemistry
Disclaimer
All claims expressed in this article are solely those of the authors and do not necessarily represent those of their affiliated organizations, or those of the publisher, the editors and the reviewers. Any product that may be evaluated in this article or claim that may be made by its manufacturer is not guaranteed or endorsed by the publisher.